FrSky Batteri NMH till Taranis QX7
NiMh Sändar acc för Taranis Q X7.
Mått: 86x58x17.5 mm. Kapacitet: 2000 mAh. Spänning: 7.2 V.
Kan naturligtvis även passa andra typer av sändare. (byte av kontakt kanske krävs).
|
|
|
|
GensAce 2700 mAh 3S Sändarbatteri FrSky Taranis X9D mfl
GensAce LiPo batteri för Sändare.
Men 3 olika anslutningar för div. radio sändare. Kontrollera vad din radio klarar. Mät batteri utrymmet (inkl utrymme för kablar), klarar radion 3S LiPo? Då kanske detta är något för dig.
Gens ace lipo 2700mAh 3S1P lipo battery pack includes special connectors made specifically for your RC radios including the very popular FrSky Taranis X9D.
A 3s balance plug, JST connector, and standard male servo connector are included for a wide compatibility of radios.
Volt: 11.1 V 3 cell Kapacitet: 2700 mAh Storlek: 93 x31 x24 mm Vikt: 200 g. Amp: 1 C kontinuerligt 2.7 A. (OBS! Sändarbatteri) Laddning : 1 C rekommenderas. Kontakter: Futaba, JST-SYP (röd kontakt), JST-XHR 3P, JST-XH Balansering, kablar 20 AWG.
Lär dig mer om batterier i vår guide!
Kontakter och adaptrar: Se här!
|
|
|
|
|
FrSky SD1 (SBUS signal to PWM)
SD1 can be used as SBUS decoder to convert SBUS signal to PWM signal for use of a conventional servo (other than use SBUS compatible servo directly) with SBUS system.
Convert the SBUS signal to the PWM signal Multiple methods to set the output channel signal
Dimension: 8mmx12mmx3.1 mm (LxWxH) Weight: 0.45 g Operating Voltage Range: 3.5V~10V Operating Current: 24mA at 5V Firmware Upgradable PWM Output Rate: 18ms/55Hz
|
|
|
|
FrSky XSR-SIM
The FrSky Wireless USB Dongle For Simulator allows you to wirelessly connect your FrSky transmitter to computer to use simulator. Then bind your transmitter to it, now you can move freely while using a simulator.
OBS! EU/LBT.
Compact design Low power requirements: typically 55mA Compatible with FrSky transmitters and module systems (Mode D16) Compatible with popular simulators (DRL, LiftOff, Freerider, HotProps, etc.) 8 proportional channel and 8 switch channel output (set on the transmitter side) Firmware upgradable (through the S.Port)
Size: 48.2x19.1x9.2 mm (LxWxH) Weight: 6.2 g
|
|
|
|
FrSky G-RX8 mini mottagare (Seglare)
This receiver is designed to be used for the Gliders. FrSky built the variometer sensor into the RX8R receiver, this will give you telemetry data like altitude and vertical speed. The G-RX8 supports the redundancy function as well, this means you can add on another receiver to create a back-up in case one fails. In addition, it supports SBUS and PWM mode, you can switch between the 2 channels between very easily.
Integrate with high precision variometer sensor Support redundancy function Support telemetry data transmission Switchable SBUS/PWM mode (1-8CH from PWM outputs and 1~16CH from SBUS output)
Dimension: 55.26x17x8mm Weight: 5.8g Number of Channels: 16 CH(1-8ch/9-16ch from conventional channel outputs, 1-16CH from SBUS port). Operating Voltage Range: 3.5-10V Operating Current: 100mA at 5V Operating Range: Full range Firmware Upgradable Compatibility: D16 mode Servo frame rate: 9ms (HS–High Speed Mode) 18ms (FS–Normal Speed Mode)
|
|
|
|
FrSky RX8R PRO
An upgraded version based on the RX8R receiver, it has all the same features including redundancy.
The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.
Strong anti-interference performance in ignition process Higher precision of PWM Lower latency on the PWM output Support redundancy function Smart Port enabled and support telemetry data transmission
Dimension: 46.3mmx26.6mmx14.2mm (LxWxH) Weight: 14.8g Numbers of Channels: 16CH(1-8CH PWM or 9-16CH PWM from conventional channel outputs, 1-16CH from SBUS port) With RSSI Output on Board: Analog DC 0-3.3V Operating Voltage Range: 3.5V-10V Operating Current: 100mA at 5V Operating Range: full range (>1.5km) Firmware Upgradeable Servo Frame Rate: 9ms (HS—High Speed Mode)/18ms (FS—Normal Speed Mode) Compatibility: FrSky transmitters/transmitter modules in D8/D16 mode
|
|
|
|
FrSky RMP Sensor
The FrSky Smart Port RPM and Temperature Sensor has been designed to work with FrSky Smart Port systems, it can measure the RPM of brushless motors from 1,000~30,000rpm and temperatures of -20 to 250 degrees celsius. Other FrSky Smart Port enabled sensors including the variometer, lipo voltage, GPS, current and airspeed sensors can be used at the same time.
Installing is easy, just connect the sensor to any 2 wires on the brushless motor by the supplied JST cable and then plug the smart port lead into the smart port enabled receiver. 2 temperature sensors are supplied which are plugged to the PCB so you can use a single one or both. Attach the temperature sensor to your ESC to enjoy the full benefit and peace of mind from this fantastic product. Set up is very straightforward using the push button and LED status indicator.
Please note: The FrSky Smart Port RPM/Temperature Sensor is only compatible with FrSky Smart Port enabled receivers such as the X8R, X6R and X4R.
Measures RPM from 1,000~30,000rpm Measures temperature from -20~250°C Simple and easy to install Small and lightweight LED status indicator Easy push button set up
Compatibility FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. Dimension 29×20×2mm Weight 6.7g Operating Voltage Range DC 4 -10 V Measurement Range -20~250 degrees Celsius/ -4~482 degrees Fahrenheit Current consumption 25mA@5V
|
|
|
|
|
|
|
|
|
|
FrSky G-RX6 mini mottagare (Seglare)
This FrSky G-RX6 is designed to be used with Gliders. FrSky built a variometer sensor right into the X6R receiver, this will give you telemetry data like altitude and vertical speed. The G-RX6 features 6 PWM outputs with higher precision and lower latency. The latency of the PWM output is 9ms less than that of the X6R, in high speed mode. It also supports the redundancy function, so it can be used in conjunction with other receivers. The G-RX6 and the whole RX-line has a 40% increased operating range compared to the previous X series receivers.
High sensitivity (40% Increase of the range compared to previous X series receivers) Integrated with high precision variometer sensor Higher precision PWM Lower latency PWM output Lower power consumption Supports redundancy function Smart Port enabled and support telemetry data transmission Battery voltage detection 2 detachable IPEX connector antennas
Dimension: 21.1×13×7.3mm (L×W×H) Weight: 2.2g / 2.6g (with two antennas) Number of Channels: 16CH (1-6CH PWM from conventional channel outputs, 1-16CH from SBUS OUT port) Operating Voltage Range: 3.5V-10V Operating Current: 100mA@5V Operating Range: >2km Servo Frame Rate: 9ms (HS—High Speed Mode)/18ms (FS—Normal Speed Mode)
|
|
|
|
FrSky STK
Verktyg för att ändra inställningar i S6R och S8R, mottagare med gyro.
Ladda ner manualen (pdf) under fliken "Dokument".
|
|
|
|
FrSky Taranis X-Lite Svart + Brace lite Combo
Get ahead of the curve with the next game changing transmitter from FrSky, the Taranis X-Lite.
This revolutionary radio blends the functionality and reliability of FrSky Transmitters with a compact Game-Style controller.The X-Lite is ergonomically designed, featuring 4 switches and 2 sliders, which means you can still fly your Fixed-wing models as well multirotors and helicopters. Compact in size means you can take it virtually anywhere. It features a Haptic Vibration Feedback System along with the voice and sound alert warnings.The X-Lite has the smoothest control possible with the pre-installed high precision M12 Lite hall sensor gimbals. The easy to access battery bay allows for quick, worry free battery swaps. The X-Lite runs on the familiar OpenTX software and the model memory is expandable with the addition of your own micro SD card. Like all of our new transmitters it has a wireless feature that lets you link up wirelessly to other FrSky radios for training, additionally it can link up to the FrSky FreeLink App for monitoring telemetry and configuring receivers.Long range is an option with the support of the upcoming R9M Lite 915/868MHz module. Other features include Receiver Match, Real-Time Flight Data Logging and Super Low Latency for competitive flying. Overall this Radio has all the features of its predecessors in a smaller package at an unprecedented value.
SPECIFICATION Number of Channels: 16 channels Weight: 308 g / 376 g (with battery) Operating Voltage Range: 6.0 - 8.4 V Operating Current: 190 mA at 7.4 V Operating Temperature: -20 - 60 degree C Backlight LCD resolution: 128x64 Model Memory: 60 models (extendible by Micro/TF card)
FEATURES Ergonomic and compact design M12 Lite gimbal Digital high accuracy hall sensor gimbal Mode conversion adjustments accessible without disassembly CNC machined gimbal pedestal High-speed internal and external module digital interface Internal: 450K, External: 420K Super low latency (Total latency < 20ms, lowest to 12ms) Compatible with new lite type external modules (R9M Lite, MPM Lite, etc.) Installed open source operating system– OpenTX Haptic vibration alerts and voice speech outputs (Headset jack and inbuilt speaker) Internal antenna and external antenna connector 128x64 outdoor readable backlight LCD Smart Port, Micro USB-B Port, Headset jack and TF card slot Easily accessible battery compartment, uses replaceable 18500 Li-ion batteries (Batteries Not Included)
Wireless function (Optional) Compatible with FrSky Free Link App Support wireless trainer system (Need additional parts or order specific model)
MORE DETAILS: https://www.frsky-rc.com/product/taranis-x-lite/
|
|
|
|
FrSky Taranis Q X7S Hall sensor gimbals Kolfiber
Inklusive Hallgimbals, hardcase tygväska, laddare och batteri.
OBS! Ingår även en R9M Long range modul!
FrSky Taranis Q X7S is the upgraded version of the original Taranis Q X7. It includes all the features of Taranis Q X7 and more.
Taranis Q X7S has the upgraded ball bearing hall sensor gimbals and is loaded with six upgraded switches and two knobs. It runs on OpenTX and files can be shared with the popular X9D Plus. The MicroSD card slot offers unlimited model memory options, it also has a USB port for upgrades and to connect to a PC for adjusting settings. Wheel and center enter button makes navigating the backlit menu easy and precise.
Equipped with an audio jack output and trainer port as well. In addition, the Taranis Q X7S also supports the wireless trainer function and it is compatible with FrSky Freelink ( https://www.frsky-rc.com/app/ ) to monitor the sensor data during the flight. And of course a module bay for use with JR-type modules that can be used with other protocol receivers and with the use of a FrSky XJT module.
This is a lightweight feature packed reliable system. The radio includes a Haptic Vibration Feedback System which provides an alternative feedback system to the voice and sound alert warnings. This radio can support up to 32-channels. Other features include Receiver Match, Real-Time Flight Data Logging and Super Low Latency for precision flying. Overall this Radio has the features of more expensive transmitters at an unprecedented value.
Hall sensor M7 gimbal Receiver match Audio speech outputs (values, alarms, settings, etc.) Real-time flight data logging Receiver signal strength indicator (RSSI) alerts Inbuilt wireless trainer system Super low latency Vibration alerts Model files are compatible with TARANIS X9D/X9D Plus/X9E/X7. Open source firmware OpenTX installed. Support connect the Free Link App for telemetry
Model Name Taranis Q X7S Transmitter Color Blue/ Carbon Fiber Number of Channels 16 channels (up to 32 channels) Operating Voltage Range 6.5~15V (2S, 3S Lipos are acceptable) Operating Current 190mA@7.2V Operating Temperature -10~60 degree C. Backlight LCD Screen 128*64 outdoor readable LCD Flash Memory 16MB(extendible by TF card) Compatibility FrSky receivers in the D8/D16/LR12 mode, Taranis Q X7S-EU version is not compatible with D8 mode.
|
|
|
|
FrSky Horus X10S Amber
The FrSky Horus X10 and X10S are the latest transmitters to join the FrSky family. They both carry on all of the features of their predecessor’s and each model has its own unique advantages.
The X10 series carries forward all the advantages of its big brother the X12S, the X10 and X10S have the built-in iXJT+ module, detachable external antenna, and an industrial LCD screen. Comes with FrSky’s own easy to use FrOS (operating system) and of course, supports OpenTX as well. The X10 series also inherits the wireless trainer system, antenna detection and SWR warning functions. Designed with 2 internal antennas to improve signal strength and improved battery life with a rechargeable Li-ion battery.
The main difference between the X10 and X10S is the Horus X10 has M10 hall sensor gimbals with adjustable sticks. The Horus X10S is equipped with our latest and best gimbal to date, the MC12P has all CNC digital higher accuracy 10 ball bearing hall sensor Gimbals than MC12 gimbal of the X12S. These gimbals offer the most precise control for your flying experience.
Built-in iXJT+ module (the enhanced RF performance and the less latency) Wireless trainer system Support FrSky Free Link App (Download link: https://www.frsky-rc.com/app/) FrSky FrOS (Support OpenTX System) 2 internal antennas and detachable external antenna Antenna detection and SWR warning Industrial LCD: 480*272 readable outdoor color screen Built-in Li-ion battery MC12P all CNC digital higher accuracy ten ball bearings hall sensor gimbals and extendable stick ends
Full Weight: 1000g Operating Voltage: DC 7.2V Operating Temperature: -10 ~ 60 degree C Operating Current: 350mA@7.2V Number of channels: 16 channels (up to 32 channels) Flash Memory: 16MB(extendible by TF card)
|
|
|
|
FrSky Horus X10S Silver
The FrSky Horus X10 and X10S are the latest transmitters to join the FrSky family. They both carry on all of the features of their predecessor’s and each model has its own unique advantages.
The X10 series carries forward all the advantages of its big brother the X12S, the X10 and X10S have the built-in iXJT+ module, detachable external antenna, and an industrial LCD screen. Comes with FrSky’s own easy to use FrOS (operating system) and of course, supports OpenTX as well. The X10 series also inherits the wireless trainer system, antenna detection and SWR warning functions. Designed with 2 internal antennas to improve signal strength and improved battery life with a rechargeable Li-ion battery.
The main difference between the X10 and X10S is the Horus X10 has M10 hall sensor gimbals with adjustable sticks. The Horus X10S is equipped with our latest and best gimbal to date, the MC12P has all CNC digital higher accuracy 10 ball bearing hall sensor Gimbals than MC12 gimbal of the X12S. These gimbals offer the most precise control for your flying experience.
Built-in iXJT+ module (the enhanced RF performance and the less latency) Wireless trainer system Support FrSky Free Link App (Download link: https://www.frsky-rc.com/app/) FrSky FrOS (Support OpenTX System) 2 internal antennas and detachable external antenna Antenna detection and SWR warning Industrial LCD: 480*272 readable outdoor color screen Built-in Li-ion battery MC12P all CNC digital higher accuracy ten ball bearings hall sensor gimbals and extendable stick ends
Full Weight: 1000g Operating Voltage: DC 7.2V Operating Temperature: -10 ~ 60 degree C Operating Current: 350mA@7.2V Number of channels: 16 channels (up to 32 channels) Flash Memory: 16MB(extendible by TF card)
|
|
|
|
FrSky Dekoder SBUS till PWM (FrSky/Futaba)
FrSky Dekoder SBUS till PWM.
Weight: 14.8 g Operating Voltage Range: 4-10 V Operating Temperature Range: -10 to 45 C Channel Output Cable Lengths: 210 mm
(Se manualen under fliken dokument, begränsningar med vissa mottagare finns.)
Du behöver även: FrSky Servo Channel Changer (SBUS)
|
|
|
|
FrSky Servo Channel Changer (SBUS)
FrSky Servo Channel Changer.
This product is a tool for setting the channel to FrSky SBUS & CPPM compatible servo (e.g. D12MB), FrSky SBUS decoder and Futaba SBUS compatible servo. In order to fully enjoy benefits of this system, please, carefully read the instruction and set up the devices as described below.
Errors When channel setting cannot be performed correctly because of improper connection of the D12MB or other SBUS compatible servo, etc., check the following: 3. Use rotate switch () set the "Set-To" to the channel you want and push rotate to confirm.
Dimension: 48x67x22 mm Weight: 6.7g Operating Voltage Range: 3-16V Operating Temperature Range: -10-45 C
|
|
|
|
FrSky S.Port AirLink-S
Upgrade S.Port devices
Configure S6R/S8R/Sensors with PC software
Configure S6R/S8R/Sensors wirelessly with Free Link (Apple Store only at present)
Compatibility: All FrSky S.Port products Dimension: 45x16x4 mm (LxWxH) Weight: 7 g
|
|
|
|
FrSky Long Range Combo Set, (R9M+R9)
Combo, bestående av R9M Modul 900 MHz + R9 Mottagare.
FrSky R9 and R9M radio control system is the first FrSky long range system which works in the frequency of 900MHz. The R9M module offers 4 switchable RF power outputs to so you can choose the appropriate power for different flight situations. Compared to another FrSky 2.4GHz long range receiver like the L9R, the R9 receiver has a longer operating range up to 10KM and above. Moreover, the R9 is also a redundancy receiver which can connect to another receiver to ensure the security of your aircraft.
900MHz working mode Uteffekt: 25 eller 500 mW. Long range, low latency and high precision RC system 4 Optional RC power Smart Port enabled and support telemetry data transmission
Compatibility: R9 Operating Voltage Range: 4V-12 V
|
|
|
|
FrSky Lipo Sensor, Smart Port
FrSky Lipo Sensor, Smart Port enable It can measure total voltage and cell voltages as connected.
Compatibility: FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. Weight: 6 g Case: 35×23×6 mm Operating Voltage Range: 2S~6S (6~25 V) Operating Temperature Range: -10~70 C
|
|
|
|
FrSky Smart Port GPS Sensor
The FrSky GPS Sensor feeds variable directional information such as altitude, position, speed, and UTC time, which is displayed in real time on FrSky’s Taranis transmitter or telemetry dashboard (DHT-U/FLD-02/FSD etc.) This sensor will only work with the FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. This is a great addition to your Taranis setup.
Compatibility: FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. Weight: 11.3 g Case: 40x20x9 mm (L x W x H) Operating Voltage Range: DC 4-10 V Operating Temperature Range: -40~85 C
|
|
|
|
FrSky Vari-H Variometer/höjd sensor (trycksensor)
The FrSky Variometer sensor calculates the altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude, using this the sensor will estimate the altitude. An exact display cannot be performed if atmospheric pressure changes in weather. The Variometer sensor also can output the Altitude Rate via DA port. Altitude Rate formula: (Output DA Voltage -1.65)/1.65=Altitude Rate speed/10.24.
Capable of connecting directly to the telemetry receivers without the sensor hub. Backward compatibility with existing sensor hub and sensors, also compatible with new generation Smart Port enabled sensors. Smart Port enabled, realizing two-way full duplex transmission.
Type: Variometer sensor Measures: -700 ~ 10000 m with 0.1 m (high precision version) resolution Operational Voltage: 4~10 VDC Operational Current: 30 mA Dimensions: 31.1×18.3x6 mm (LxWxH) Weight: 3.1 g Units: Metric or British units
|
|
|
|
FrSky Battery Voltage Sensor
FrSky Battery Voltage Sensor – FrSky telemetry system accesory.
Three Voltage Ranges To Choose: 1S Lipo for battery voltage range from 0V~6.6V; 3S Lipo for battery voltage range from 0V~13.2V; 5S Lipo for battery voltage range from 0V~19.8V.
|
|
|
|
FrSky Smart Port Current Sensor 150A
FrSky’s Smart Port Current Sensor-150A.
It is designed for FrSky Smart Port enabled systems, and can measure Current (A) when connected between a Battery and ESC.
Compatibility: FrSky Smart Port enabled receivers, such as X8R,X6R, X4R, etc. Model: FCS-150A Weight: 20.1 g Measurement Range: 0~150 A Maximum Current: 150 A
|
|
|
|
FrSky Hastighets Sensor 360 Km/h (Pitot rör)
The FrSky air speed sensor was designed for the FrSky smart port enabled system. With its easy install it is an easy way to get air speed data. Just install the pitot tube as far away from any prop wash or any disturbed air as possible, install the sensor in the fuselage, run the silicon tubes, and plug into the receiver, or another smart port sensor, and enjoy!
This sensor not only can send speed data to your Taranis, but can also, when set up properly, warn the pilot of low airspeed, log airspeed data, check your top speed, program your radio automatically drop the landing gear at a preset airspeed, etc.
There are 2 versions of air speed sensors. The SP-ASS-70 can accurately measure airspeed up to 167.7 mph, (270 km\h). The SP-ASS-100 measures up to 223.7 mph, (360 km/h).
Compatibility: FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. Model: ASS-100 Dimension: Circuit Board: Weight 5 g, dimensions 33.14×17.14×10.45 mm Pitot Tube: Weight 4 g, length 101mm, diameter 2.6 mm
Pitot Tube Hose: Silicon, clear, 3 feet (1 meter), 2.2 mm ID, 3.8 mm OD Operating Voltage Range: DC 4 -10 V Operating Current: 25mA at 5 V Measurement Range: 0~360 km/h
|
|
|
|
FrSky Hastighets Sensor 270 Km/h (Pitot rör)
It is designed for FrSky Smart Port enabled system, and can provide Air Speed data for your entire flight.
Compatibility: FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc. Model: ASS-70 Operating Voltage Range: DC 4-10 V Operating Current: 20 mA at 5 V Measurement Range: 0~270 km/h. Size/Weight: 7 g, dimensions 33.29×22.26×12.55 mm. Pitot Tube: Weight 4 g, length 101 mm, diameter 2.6 mm.
Pitot Tube Hose: Silicon, clear, 3 feet (1 meter), 2.2 mm ID, 3.8mm OD
|
|
|
|
FrSky Vari-N Variometer/höjd sensor
The FrSky Variometer sensor calculates the altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude, using this the sensor will estimate the altitude. An exact display cannot be performed if atmospheric pressure changes in weather. The Variometer sensor also can output the Altitude Rate via DA port. Altitude Rate formula: (Output DA Voltage -1.65)/1.65=Altitude Rate speed/10.24.
Capable of connecting directly to the telemetry receivers without the sensor hub. Backward compatibility with existing sensor hub and sensors, also compatible with new generation Smart Port enabled sensors. Smart Port enabled, realizing two-way full duplex transmission.
Type: Variometer sensor Weight:3.1 g Operating Voltage Range: DC 4-10 V Operational Current: 30 mA Dimensions: 31.1×18.3x6 mm (LxWxH)
|
|
|
|
FrSky Temperatur Sensor 250 C
Up to two temperature sensors can be used at the same time. They are commonly used to read temperatures of model accessories, such as electric motor, ESC, glow and gas engine cylinder head, battery, muffler, voltage regulator, BEC, tail pipe and ambient air.
Measurement Range: -20~250 degrees Celsius Accuracy: 1 degree Celsius
|
|
|
|
FrSky FSH Sensor Hub
FrSky Sensor Hub is recommended to connect digital side port (G, TX, RX) of FrSky telemetry receiver and FrSky sensors by the provided cable, to serve as an information collecting and processing center, monitor the model status and feedback all data back to FrSky DHT-U.
Weight: 7g (sensor hub only w/o wires) Operating Voltage Range: 4-10 V Operating Temperature Range: -20~80 C Dimensions: 37x30x8 mm
|
|
|
|
|
|
|
|
FrSky R-XSR ultra mini receiver
FrSky ultra mini receiver R-XSR is the evolution of FrSky full range XSR receiver.
The R-XSR is a standalone receiver with all the functions of XSR, in addition, it’s almost 1/3 size and 1/3 weight of XSR receiver. Moreover, there redundancy function is integrated into this tiny receiver ensures the security, and the IPEX connector makes it more convenient for you to replace antennas.
Ultra mini size and light weight Support telemetry and Smart Port enabled Full range Switchable SBUS/ CPPM signal output Supports redundancy function IPEX connector, replaceable antennas
Dimension: 16x11x5.4 mm (LxWxH) Weight: 1.5 g Number of channels: 16 CH (1-16 CH from SBUS channel, 1~8 CH from CPPM channel) Operating Voltage Range: 3.5 V~10 V Operating Current:70mA at 5 V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode
|
|
|
|
FrSky S6R med 3-axlig stabilisering
Built-in a three-axis gyro and three-axis acceleromter sensor module Built-in RSSI PWM ourput (0~3.3V) on board Built-in battery voltage sensor Smart Port enabled
Compatibility FrSky Taranis X9D Plus/X9E/Horus X12S/XJT in D16 mode S6R-EU only works with Horus X12S and Taranis X9D Plus/X9E-EU/XJT-EU in D16-EU mode Model X6R(6CH receiver with buil-in 3-axis gyro and 3-axis acceleration) Dimension: 47.42x23.84x14.7 mm (LxWxH) Weight: 12.1 g Operating Range: full range Operating Voltage Range: 4.0~10 V Operating Current: 100 mA at 5 V Number of Channels: 6 CH(1~6 CH from conventional channel outputs) Measurement Range: +/- 4 g
|
|
|
|
FrSky S8R med 3-axlig stabilisering
The S8R is a FrSky X-series receiver with built in 3-axis stabilization. For conventional Fixed Wing and Glider Models it will support stabilization, automatic level, hover and Knife-edge flight modes, for Delta Wings or flying wings and V-tail models it supports stabilization and automatic level flight modes. You can edit the type of model and manipulate all these features via the S8R.Config or S8R.lua. The S8R can also be used as a standard 8 channel X series receiver if it is required.
Tip: Use the S8R with 3-axis stabilization as a slave receiver with the RB-10 to give you that extra peace of mind by buying you precious time to bring your model home.
Built in RSSI PWM output (0-3.3V) Built in battery voltage detection Built in 3-axis gyroscope and 3-axis accelerometer sensor module Smart Port enabled SBUS Port enabled
Compatibility: FrSky Taranis X9D Plus/X9E/X7/Horus X12S/XJT in D16 mode S8R-EU only works with FrSky Taranis X9D Plus/X9E/X7/Horus X12S/XJT in D16-EU mode Firmware Upgradable Dimension: 46.47x26.78x14.12 mm (LxWxH) Weight: 14 g
Operating Range: Full range Operating Voltage Range: 4.0-10 V Operating Current: 120 mA at 5V
Number of Channels: 8/16 CH (1-8 ch from conventional channel outputs, 1-16 ch from SBUS output) RSSI(Y/N): With RSSI PWM output on board: PWM voltage output(0-3.3 V), 100Hz, 1500+/-500us
Measurement Range: Gyroscope Measurement Range: +/-2000dps Accelerometer Measurement Range: +/-4 g
|
|
|
|
FrSky Horus X10S Carbon
The FrSky Horus X10 and X10S are the latest transmitters to join the FrSky family. They both carry on all of the features of their predecessor’s and each model has its own unique advantages.
The X10 series carries forward all the advantages of its big brother the X12S, the X10 and X10S have the built-in iXJT+ module, detachable external antenna, and an industrial LCD screen. Comes with FrSky’s own easy to use FrOS (operating system) and of course, supports OpenTX as well. The X10 series also inherits the wireless trainer system, antenna detection and SWR warning functions. Designed with 2 internal antennas to improve signal strength and improved battery life with a rechargeable Li-ion battery.
The main difference between the X10 and X10S is the Horus X10 has M10 hall sensor gimbals with adjustable sticks. The Horus X10S is equipped with our latest and best gimbal to date, the MC12P has all CNC digital higher accuracy 10 ball bearing hall sensor Gimbals than MC12 gimbal of the X12S. These gimbals offer the most precise control for your flying experience.
Built-in iXJT+ module (the enhanced RF performance and the less latency) Wireless trainer system Support FrSky Free Link App (Download link: https://www.frsky-rc.com/app/) FrSky FrOS (Support OpenTX System) 2 internal antennas and detachable external antenna Antenna detection and SWR warning Industrial LCD: 480*272 readable outdoor color screen Built-in Li-ion battery MC12P all CNC digital higher accuracy ten ball bearings hall sensor gimbals and extendable stick ends
Full Weight: 1000g Operating Voltage: DC 7.2V Operating Temperature: -10 ~ 60 degree C Operating Current: 350mA@7.2V Number of channels: 16 channels (up to 32 channels) Flash Memory: 16MB(extendible by TF card)
|
|
|
|
FrSky Taranis Q X7S Hall sensor gimbals Blå
Inklusive Hallgimbals, hardcase tygväska, laddare och batteri.
OBS! Ingår även en R9M Long range modul!
FrSky Taranis Q X7S is the upgraded version of the original Taranis Q X7. It includes all the features of Taranis Q X7 and more.
Taranis Q X7S has the upgraded ball bearing hall sensor gimbals and is loaded with six upgraded switches and two knobs. It runs on OpenTX and files can be shared with the popular X9D Plus. The MicroSD card slot offers unlimited model memory options, it also has a USB port for upgrades and to connect to a PC for adjusting settings. Wheel and center enter button makes navigating the backlit menu easy and precise.
Equipped with an audio jack output and trainer port as well. In addition, the Taranis Q X7S also supports the wireless trainer function and it is compatible with FrSky Freelink ( https://www.frsky-rc.com/app/ ) to monitor the sensor data during the flight. And of course a module bay for use with JR-type modules that can be used with other protocol receivers and with the use of a FrSky XJT module.
This is a lightweight feature packed reliable system. The radio includes a Haptic Vibration Feedback System which provides an alternative feedback system to the voice and sound alert warnings. This radio can support up to 32-channels. Other features include Receiver Match, Real-Time Flight Data Logging and Super Low Latency for precision flying. Overall this Radio has the features of more expensive transmitters at an unprecedented value.
Hall sensor M7 gimbal Receiver match Audio speech outputs (values, alarms, settings, etc.) Real-time flight data logging Receiver signal strength indicator (RSSI) alerts Inbuilt wireless trainer system Super low latency Vibration alerts Model files are compatible with TARANIS X9D/X9D Plus/X9E/X7. Open source firmware OpenTX installed. Support connect the Free Link App for telemetry
Model Name Taranis Q X7S Transmitter Color Blue/ Carbon Fiber Number of Channels 16 channels (up to 32 channels) Operating Voltage Range 6.5~15V (2S, 3S Lipos are acceptable) Operating Current 190mA@7.2V Operating Temperature -10~60 degree C. Backlight LCD Screen 128*64 outdoor readable LCD Flash Memory 16MB(extendible by TF card) Compatibility FrSky receivers in the D8/D16/LR12 mode, Taranis Q X7S-EU version is not compatible with D8 mode.
|
|
|
|
FrSky FSD Smart Port Display
1) Show all connected sensors data;
2) Capable of programming alarm thresholds and system settings;
3) Set Physical ID and Group Number for S.Port sensors;
4) Firmware upgradeable for all S.Port products.
Compatibility FrSky X Series Telemetry Modules Model FSD (FrSky S.Port Dashboard) Dimension 75*50*13.8mm Operating Voltage Range 4.8V ~ 6V Pixel 128*64
|
|
|
|
FrSky FrUSB-3 (FUC-3) Upgrade Cable
This is an FrSky firmware upgrading cable for various components and transmitters. The firmware can be downloaded from the FrSky website.
This upgrade cable is suitable for DFT/DJT/DHT/8ch Telemetry Receiver/Sensor Hub/FLD-02.
|
|
|
|
FrSky SPC
FrUSB-3+SPC could upgrade all Smart Port enabled products, including XJT, X8R, X6R and smart port sensors
|
|
|
|
FrSky USB to S.Port
New Frsky USB to S.Port Update Adaptor for transfering files and firmware to the Taranis and S.Port receivers and sensors. comes with separate S.Port cable
This new unit now superceeds the Frusb-3 cable and Smart port adapter.
Ladda ner program här: https://www.frsky-rc.com/usb-to-s-port/
|
|
|
|
FrSky M7 Gimbal till Taranis Q X7
Upgrade your Taranis Q X7 with this plug-n-play high resolution M7 Gimbal from FrSky. The highly sensitive Hall sensors will not wear out quickly. It has an extremely smooth feel with the quad ball-bearings and the metal outer construction. Thicker 4mm stick ends give you a solid link to your controls. Fully adjustable tension and easily disable the self centering axis with one screw. This is a must have accessory for achieving those precision flight maneuvers.
Hall sensor 4 ball-bearings Adjustable tension Can be enable or disable self centering on both axis and ratcheting on the Y axis Special material quality that wears well
Model: Gimbal-M7 Supply Voltage (VCC): DC 3.0 +/-0.5V Sensitivity: 2.50 mV/G Linear Output Voltage Range: 0.1 (VCC +0.1) V Output Load Resistance (output to ground) >15KQ Quiescent Output (TA = 25 degree C, B = 0 G): 0.5 x VCC Noise (no load): <40mVpp Quiescent Output Power Supply Rjection: -69dB
|
|
|
|
|
|
FrSky M9 Gimbal till Taranis X9D
Upgrade your Taranis X9D with this plug-n-play high resolution M9 Gimbal from FrSky. The highly sensitive Hall sensors will not wear out quickly. It has an extremely smooth feel with the quad ball-bearings and the metal outer construction. Thicker 4mm stick ends give you a solid link to your controls. Fully adjustable tension and easily disable the self centering axis with one screw. This is a must have accessory for achieving those precision flight maneuvers.
Hall sensor 4 ball-bearings Adjustable tension Ideal for FPV RACING, 3D and acrobatic fixed wing, 3D Heli
Supply Voltage (VCC): DC 3.0 +/- 5V Sensitivity: 2.50 mV/G Linear Output Voltage Range: 0.1 (VCC +0.1) V Quiescent Output (TA = 25 C, B = 0 G): 0.5 x VCC Noice (no load): <40 mVPP
|
|
|
|
FrSky M9-R Gimbal
FrSky M9-R Gimbal is specially designed for FPV racing, 3D and acrobatic fixed wing and 3D Heli pilots who are using the FrSky Taranis X9D/X9D Plus Transmitter. The 45 degree throttle travel will allow you to achieve a quick throttle response resulting in precision control. The combination of a hall sensor gimbal and included lotus stick ends will assure that your thumbs or fingers are with one with the radio. We gave it a red metal body to give it that race ready look.
45 degree throttle travel for quick throttle response Hall sensor 4 ball-bearings Adjustable tension Ideal for FPV RACING, 3D and acrobatic fixed wing, 3D Heli
Supply Voltage (VCC): DC 3.0 +/- 5V Sensitivity: 2.50 mV/G Linear Output Voltage Range: 0.1 (VCC +0.1) V Quiescent Output (TA = 25 C, B = 0 G): 0.5 x VCC Noice (no load): <40 mVPP
|
|
|
|
FrSky V8R4-II Mottagare 4-kan
The V8R4-II lightweight receiver is a great fit for small Park Fliers, 3D foamy and indoor slow flyers.
Weighing in at a scant 3.5 grams, this is the perfect receiver for these types of applications. This receiver will operate as normal with your Telemetry module without having to switch over to none telemetry mode. Also compatible with the none telemetry modules – as well as with both the TARANIS TX and the XJT module too.
|
|
|
|
FrSky X4R Mottagare 4-kan ACCT Telemetry
X4R receiver features 4 PWM outputs (normal servo) and now includes an option for CPPM output for feeding to flight controllers or other uses. CPPM carries 8 channels on a single servo wire. SmartPort and a traditional A2 port are all located on the side of the receiver and allow you to connect all sorts of great sensors to send data back to your FrSky radio.
RSSI (PWM) output Lighter weight and physically smaller than D8R-II & D6FR Two selectable failsafe setting options – native failsafe or user programmable failsafe External analog telemetry port (AD2)
Compatibility FrSky X-series Module (XJT etc.) & Taranis X9D in D16 mode(X4R is not work with D-series Module) Dimension 40x22.5x6 mm (L x W x H) Weight 5.8 g Operating Range full range (>1.5km) Operating Voltage Range 4.0-10 V Operating Current 100 mA at 5 V Number of Channels 4 Ch from conventional channel outputs, without SBUS port
|
|
|
|
FrSky XSR-M 16Ch (1-16ch from SBUS channel, 1-8 ch from CPPM
FrSky XSR-M full duplex telemetry receiver. In order to fully enjoy the benefits of this system, please read the instruction manual carefully and set up the device as described.
Smart Port enabled. S-BUS/CPPM output (BLUE LED stay lit indicates XSR-M in S-BUS mode, otherwise in CPPM mode) Firmware Upgradable
Compatibility FrSky X-series Module & radios in D16 mode Dimension 20x20x1mm (L x W x H) Weight 1.8g Operating Voltage Range 4.0-10V Number of Channels 16Ch (1-16ch from SBUS channel, 1-8ch from CPPM channel)
|
|
|
|
FrSky Horus X12S (inkl. Alu.väska). Silver
Horus X12S + Aluminiumväska.
FrSky introduce the newest and most powerful radio, the horus x12s. The Horus is the new flagship radio from FrSky with premium gimbals, pots, switches and components. The radio also has a built in GPS module, speaker, haptic feedback and more. The X12S features a full color LCD screen with an easy to navigate UI system. Each radio comes with a high quality hard case for transportation.
Audio Speech Outputs (values, alarms, settings, etc.) Full telemetry and real-time data logging Antenna detection and SWR warning Integrated GPS module and 6-axis sensor (3-axis gyro and 3-axis accelerator) All CNC 6 ball bearings gimbals with accuracy hall sensor and extensible by stick ends Safe power switch with integrated strap base Two types trainer ports Inbuilt wireless trainer system 6 position encoder for easier flight modes switch FrSky FrTX operation system MP3 Player Industrial High Resolution TFT Screen Readable Outdoor Internal and External Antenna selectabl - SD card is not supplied with X12S Horus, please purchase separately.
Compatibility FrSky X series, D series, L series and V8-II series receivers (plus other receivers if an external module is used) Operating Voltage Range DC9.6V Number of Channels 16 channels (Up to 32 channels) Operating Temperature Range -10-60 Grader C.
|
|
|
|
FrSky X8R 2.4 GHz 16 kan. Rx SBUS Smart Port
FrSky's newest receiver features 16 channels (8 normal pwm outputs and all 16 channels on the dedicated Sbus output). Plus the exciting new Smart Port.
Smaller than the previous 8 channel recievers, but now packing 16 channels and the new Smart Port that supports the new hubless digital sensors! Or, connect the new vario, and then connect the old hub to use existing analog sensors.
A common question we get is how do you get all 16 channels out of the X8R? Well, FrSky has given you options. You can use the Sbus line to access all 16 channels. Using something like the FrSky Sbus Decoder, you can convert the digital Sbus signal to normal servo outputs. You can connect Sbus servos directly to the Sbus line, frSky will have several servo options very soon. Or you can combine 2 X8Rs and output channels 1-8 on the first reciever, and output 9-16 on the second reciever.
But that isn't all the X8R can do. It can also work in "D8 Mode to work with the DHT, DJT, DFT and DHT-U transmitter modules. In this mode you have 8 channels. The neat trick is the Smart Port still works in D8 Mode!
You are probably wondering about the new antennas on the X8R. FrSky refers to these as PCB antennas and report upto a 20% range increase over the standard antennas. (The X8R is also available with a standard antenna version, handy for full carbon aircraft.)
Specification:
Dimension: 46.5mm x 27mm x 14.4mm (1.83" x 1.06" x .56") Weight: 16.8g (.59 oz) Operating Voltage Range: 4V-10.0V Operating Current: 100mA@5V Operating Range: >1.5km (Full Range) RSSI output: analog voltage output (0~3.3V) FirmwareUpgradeable Compatibility:
All 16 channels requires the FrSky Taranis, or the XJT module. For 8 channels in D8 Mode you can use the FrSky Taranis or XJT, DJT, DFT, DHT and DHT-U modules.
|
|
|
|
FrSky X6R 2.4 GHz 16 kan. Rx ACCST SBUS Smart Port
FrSky's X6R receiver features 16 channels (6 normal PWM outputs and all 16 channels on the dedicated Sbus output). Plus the exciting new Smart Port and a traditional A2 port on the bottom. Pull the jumper and connect an FBVS for basic external voltage monitoring.
Smaller than the X8R, but still packing 16 channels and the new Smart Port that supports the new hubless digital sensors! Or, connect the new vario, and then connect the old hub to use existing analog sensors.
Features
With external analog telemetry port(AD1), When pins of A1 and X (Middle Pin) are connected by the jumper, A1 will change from External Analog Telemetry Port to Internal Built-in battery voltage sensor. More number of channels: 1~6ch from conventional channel outputs, 1~16ch from SBUS port With RSSI PWM output (0~3.3V) on board Smart Port enabled, realizing two-way full duplex transmission. Specifications
Dimension: 47x23x14mm (L x W x H) Weight: 16.7g Antenna: 150mm Coaxial Antenna with packing Number of Channels: 16CH (1~6ch from conventional channel outputs, 1~16ch from SBUS port) With RSSI output on board: PWM voltage output (0~3.3V) Operating Voltage Range: 4.0~10V Operating Current: 100mA@5V Operating Range: full range (>1.5km) Firmware Upgradeable Compatibility: FrSky DFT/DJT/DHT/DHT-U in D_mode; FrSky Taranis X9D/XJT in D8 mode; FrSky Taranis X9D/XJT in D16 mode Compatibility
All 16 channels requires the FrSky Taranis, or the XJT module bound in D16 mode. For 8 channels in D8 Mode you can use the FrSky Taranis or XJT, DJT, DFT, DHT and DHT-U modules. Smart Port (S. Port) is a signal wire full duplex digital transmission interface developed by FrSky Electronic Co., Ltd. All products enabled with Smart Port (including XJT module, X6R and X8R receiver, new hub-less sensors, new Smart Dashboard, etc), serial port user data and other user input/output devices can be connected without limitations for numbers or sequences at a high transmission speed.
|
|
|
|
FrSky XM PLUS (Mini SBUS Non-telemetry Full Range)
SPECIFICATION Compatibility FrSky D16 mode Dimension 21.5*12*3.5mm(L x W x H) Weight 1.6g Operating Range Full range Operating Voltage Range 3.7V~10V Operating Current 30mA at 5V Number of Channels Up to 16CH from SBUS(CH1~CH15 for PWM,CH16 RSSI for FC)
EU firmware. Går att flasha om via radion.
|
|
|
|
FrSky Taranis Q X7 2.4GHz 16 kan. Svart
FEATURES:
Quad Ball Bearing Gimbals Receiver Match Audio Speech Outputs (values, alarms, settings, etc.) Real-time Flight Data Logging Receiver Signal Strength Indicator (RSSI) Alerts Super Low Latency Vibration Alerts Model files are compatible with TARANIS X9D/X9D Plus/X9E. Open source firmware OpenTx installed.
SPECIFICATION:
Operating Voltage Range 6~15V (2S, 3S Lipos are acceptable) Operating Current 210mA maximum (both RF module and backlit are on) Number of Channels up to 16 channels Operating Temperature Range -10~45 C Backlight LCD Screen 128*64 outdoor readable LCD Model Memories 60 (extendable by MicroSD (TF) card)
EU firmware. Går att flasha om med minneskort OBS! Att radion levereras utan batteri. Se rekommendationen nedan! Batterifacket är tomt.
|
|
|
|
FrSky X4R-SB 2.4G 3/16 kan. ACCST Telemetry Rx SBUS
FrSky 2.4G 3/16ch ACCST X4R-SB Telemetry Receiver - SBUS Edition
Dimension: 40×22.5×6mm (L × W × H) Weight: 5.8 g Number of Channels: X4RSB-3/16 ch (1~3ch from conventional channel outputs, 1~16 ch from SBUS channel) Operating Voltage Range: 4.0~10 V Operating Current: 100 mA at 5 V Operating Range: full range (>1.5 km) With RSSI output on board: PWM voltage output (0~3.3 V) Firmware Upgradeable Compatibility: FrSky X-series Module (XJT etc. ) & Taranis X9D in D16 mode (X4R / X4RSB is not work with D-series Module)
|
|
|
|
FrSky V8FR-II 8-kan HighVoltage
FrSky V8FR-II HV
Antal kanaler: 8 Storlek: 44x24x14 mm. Vikt: 9.3 g. Räckvidd: Full range, >1.5 Km. Driftspänning: 3-16 V, (High Voltage). Strömförbrukning: 30 mA.
|
|
|
|
FrSky SBUS till CPPM Converter
FrSky SBUS till CPPM Converter.
Converts the SBUS signal into CPPM without the need for any soldering. Simply plug into your SBUS receiver port and your control servo and it will decode the SBUS signal to CPPM. A full instruction manual is included with the decoder for easy use.
Brand: FrSky Item: SBUS to CPPM Decoder Weight: 4.1 g Dimensions: 250 x 13 x 5 mm Operating Voltage: 4-10 V DC Max Current: 700 mA Operating Temp Range: -10 ~ 80 (Degrees C) Usae: key for SBUS to CPPM
WARNING The input current should match the converters proper operating condition. There is the danger of erroneous operation or damage.
|
|
|
|