COMBO Erbjudande!

RC Factory Clik 25.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och adapterkabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Clik 25.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och adapterkabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Clik 25.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och adapterkabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

The Clik 25 is the successor to the famous Clik series of aircraft. It is a 4mm EPP plane, which makes the model almost indestructible. Due to several modifications compared to the previous version, the CLIK 25 becomes once again a slightly better version of itself. For example, an extended fuselage for better stability and easier balancing with lighter power combo, a higher fuselage for better lateral guidance, and lots of little things that take this model further again.

Key Features:
Wingspan: 840 mm
Lenght: 950 mm
AUW: 115-130 g

Package Includes:
Kit with Hardware , without equipment set

The Clik 25 is the successor to the famous Clik series of aircraft. It is a 4mm EPP plane, which makes the model almost indestructible. Due to several modifications compared to the previous version, the CLIK 25 becomes once again a slightly better version of itself. For example, an extended fuselage for better stability and easier balancing with lighter power combo, a higher fuselage for better lateral guidance, and lots of little things that take this model further again.

Key Features:
Wingspan: 840 mm
Lenght: 950 mm
AUW: 115-130 g

Package Includes:
Kit with Hardware , without equipment set

The Clik 25 is the successor to the famous Clik series of aircraft. It is a 4mm EPP plane, which makes the model almost indestructible. Due to several modifications compared to the previous version, the CLIK 25 becomes once again a slightly better version of itself. For example, an extended fuselage for better stability and easier balancing with lighter power combo, a higher fuselage for better lateral guidance, and lots of little things that take this model further again.

Key Features:
Wingspan: 840 mm
Lenght: 950 mm
AUW: 115-130 g

Package Includes:
Kit with Hardware , without equipment set

Laminatplast som värms på modellen.

Gjord för ex. EPP.
Tjocklek: 34 my.
Bredd: 32 cm
Längd: 6 m
Utförande: Matt

The new transparent iron-on film with enhanced adhesion, which can be applied directly to EPP, is now available.
It tolerates a wide range of temperatures on a typical modeling iron, but we advise testing it first on a sample of EPP and beginning with the temperature set to the lower third of the control dial.
For digitally controlled irons, we recommend a temperature range of 120-140°C.

This new iron-on film exhibits significantly improved adhesion to both printed and unprinted EPP surfaces, thus eliminating the need for additional bonding materials like the popular 3M 77 contact adhesive in most cases.
Its minimal thermal shrinkage ensures that the treated parts remain undistorted.

The film is offered in a thickness of 34µm, with a width of 320mm available in matte and glossy finishes, and a 75µm thickness, 305mm wide in a glossy finish. The 1.5m length is suitable for treating floats and other experimental projects, while the 6m length provides ample coverage for all our models. We recommend the 34µm thickness for all our models and floats.

Should you require increased strength and resilience at the expense of weight, we suggest using the 75µm film, particularly for models such as the Fury, Stigra, and Air truck.

Laminatplast som värms på modellen.

Gjord för ex. EPP.
Tjocklek: 34 my.
Bredd: 32 cm
Längd: 6 m
Utförande: Blank

The new transparent iron-on film with enhanced adhesion, which can be applied directly to EPP, is now available.
It tolerates a wide range of temperatures on a typical modeling iron, but we advise testing it first on a sample of EPP and beginning with the temperature set to the lower third of the control dial.
For digitally controlled irons, we recommend a temperature range of 120-140°C.

This new iron-on film exhibits significantly improved adhesion to both printed and unprinted EPP surfaces, thus eliminating the need for additional bonding materials like the popular 3M 77 contact adhesive in most cases.
Its minimal thermal shrinkage ensures that the treated parts remain undistorted.

The film is offered in a thickness of 34µm, with a width of 320mm available in matte and glossy finishes, and a 75µm thickness, 305mm wide in a glossy finish. The 1.5m length is suitable for treating floats and other experimental projects, while the 6m length provides ample coverage for all our models. We recommend the 34µm thickness for all our models and floats.

Should you require increased strength and resilience at the expense of weight, we suggest using the 75µm film, particularly for models such as the Fury, Stigra, and Air truck.

The checker displays the voltage of individual cells and triggers a loud sound signal when it falls below the set value. The voltage threshold for alarm can be set.

Key Features:
Size: 40x25x11mm
Weight: 9g
Supported batteries: 1-8S Lipo

Introducing the "Jabberwocky" – a high-performance 3D bush-high wing EPP model, designed by Cody Wojcik and inspired by the mythical creature of lore. Just like its namesake, the Jabberwocky boasts unparalleled agility and power, ready to conquer the skies with massive 3D capabilities. Crafted with precision and attention to detail, it features our renowned EPP foam construction for extreme durability. Get ready for an epic adventure with the Jabberwocky – a true masterpiece of flight engineering that breathes life into legend in the skies above.

Key Features
Wingspan: 1100 mm
Lenght: 140 mm
AUW: 600 - 650 g
Motor: 2217
ESC: 35A
Servo: 4 x 6 g, 2x 10 g
Battery: 3s 600-1300mAh
Propeller: 8x4 / 8x4.1 APC

Ingår:
Modell med landställ och tillbehör. Ej motor/fartreglage/servon mm.

Introducing the "Jabberwocky" – a high-performance 3D bush-high wing EPP model, designed by Cody Wojcik and inspired by the mythical creature of lore. Just like its namesake, the Jabberwocky boasts unparalleled agility and power, ready to conquer the skies with massive 3D capabilities. Crafted with precision and attention to detail, it features our renowned EPP foam construction for extreme durability. Get ready for an epic adventure with the Jabberwocky – a true masterpiece of flight engineering that breathes life into legend in the skies above.

Key Features
Wingspan: 1100 mm
Lenght: 140 mm
AUW: 600 - 650 g
Motor: 2217
ESC: 35A
Servo: 4 x 6 g, 2x 10 g
Battery: 3s 600-1300mAh
Propeller: 8x4 / 8x4.1 APC

Ingår:
Modell med landställ och tillbehör. Ej motor/fartreglage/servon mm.

Timer till RCFactory Flash CL.

Electronic timer for Control Line models

 Electronic timer for controlling an AC controller
 Easily adjustable flight time and delay from battery connection to actuator start-up
 Suitable for Flash CL ( control line )

Linkontroll till RCFactory Flash CL.

Complete control kit for control line models - directly designed for Flash Control Line.

Package Includes
Plastic handle
28m kevlar rope
carabiners
spool
set of screws
tube for guiding the rope
clips

Linstyrd modell från RCFactory!

Köp till drivlina, linor och timer separat.

As the name suggests, this model is a cable driven - Control line model

It is the oldest way of controlling the model from the time when RC kits did not exist yet.
With the advent of "RC" kits, this method of control has receded somewhat, but to this day
many racing categories are still flown with tethered models and are very popular.
And we know why - it's great fun! After all, this was written by Mr. Ing. Jaromír Schindler in 1954

"We see the importance of tethered models mainly in the fact that the modeler, while flying a control line model, becomes familiar, sometimes at the cost of breaking the model, with the function of the elevator"

The controls are very simple, being limited to elevator with flap support only.

We are fully aware that the Flash CL will be used primarily as a training model.
Therefore, we have subordinated the flight characteristics to this: the model flies slower than usual for other tethered models,
yet it doesn't lose the much-needed line pull even in the craziest of overhead turns.
Even though it is a training model, it can handle all aerobatic turns.
The flight characteristics are pleasant (not tricky) and in case of an accident the model is easily repairable with ordinary instant glue.
Its advantages also include a smaller flight space requirement and low purchase cost (you don't need an RC system).

You can control the motor in two ways: either by any receiver with an RC kit, or by a dedicated timer.

And please note one more thing - it is very addictive ...

Key Features
Wingspan: 870mm
Lenght: 865mm
AUW: 250g

Package Includes
Complete kit including carbon landing gear

Kit does not include control line set.

Flottörer till RCFactory Piper SC och Step 2.

Key Features:
Lightweight EPP floats
Complete set of jewellery (screws, nuts) to attach
Second landing gear
Foil to iron on and improve float characteristics
Plastic plate for attaching rear landing gear legs

Flap-kit till RCFactory Piper SC

Additional Flaperon kit for Piper SC

The Piper SC was designed by Jan Sedlacek, the world champion in pylon racing, as a multifunctional aircraft for every more or less experienced pilot.

The construction is in standard EPP thickness, so the Piper is durable and almost unbreakable. The model is calm and stable in the air, yet for first launches, choose a windless model.

The easily removable wing makes transport easy even when travelling for example on holiday. The Piper SC comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can even take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.

Key Features
Wingspan: 1150 mm
Length: 850 mm
AUW: 380 g
Motor: 2206
Regulator: 15A
Servo: 4 x 10g
Battery: 600 3S, 600 2S (25C)
Propeller: 8x4.1

Package Includes
Complete kit with fully carbon landing gear, without electronic

The Piper SC was designed by Jan Sedlacek, the world champion in pylon racing, as a multifunctional aircraft for every more or less experienced pilot.

The construction is in standard EPP thickness, so the Piper is durable and almost unbreakable. The model is calm and stable in the air, yet for first launches, choose a windless model.

The easily removable wing makes transport easy even when travelling for example on holiday. The Piper SC comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can even take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.

We offer tuning kits for the Piper, both additional flaps and floats! Feel free to take a look and try it out!

Key Features
Wingspan: 1150 mm
Length: 850 mm
AUW: 380 g
Motor: 2206
Regulator: 15A
Servo: 4 x 10g
Battery: 600 3S, 600 2S (25C)
Propeller: 8x4.1

Package Includes
Complete kit with fully carbon landing gear, without electronic

Bungee launcher allows you to launch the model on the plane to the thermals or in poor conditions on the slope even in one person.

Bungee set consists of several meters of rubber and kevlar. The model must have a hook to launch on the bungee, it is already supplied in the kit.

The kit contains 4m of TAN 3x1 rubber + 28m of lightweight Kevlar, a ring, a flagpole, a ground pin for attaching the rubber.
The kit is tuned for pulling the model up to a sufficient height and for "catching" thermals, an ideal accessory for flying with Rookie.

Key Features:
4m TAN 3x1
28m Kevlar
hook
camber
dowel pin

Some 180° servos require PWM values in the range of 500-2500uS to work in the full range.
When using a PWM signal from a standard receiver with a range of 1000-2000uS, you will not use the entire 180° range of the servo.
This servo expander expands the classic 1000-2000uS range to the 500-2500uS range.
Just connect it between the RC receiver and the servo.

Key Features:
Input voltage: 3.6-16V
PWM input range: 1000-2000uS
PWM output range: 500-2500uS

Radiostyrd!

The Rookie was designed as an addition to your modeling activities for your children or wives to keep them from getting bored with you on the field.

They can just throw it around like a thrower and when they get bored you give them the transmitter.
For example, you can mark out the landing area and the take-off line on the pad for them.
Or you can tow them behind almost any epp model 1 to 3 at a time.
They can then compete to see who lands last.
During the tow, the Rookie doesn't have to steer at all, just disengage by fully pulling the elevator when altitude is reached.
Don't have a suitable model for towing at hand? No problem, the Rookie is easily towed on a rubber band folded
made of about 5m of 3x1 rubber and 20-30m of Kevlar thread (silon) finished with a ring (for keys).
And now you have time to work on your own model, because with the Rokkie model you don't have to worry about letting
to fly anyone without your supervision. Due to its extra light weight and stability, the risk of damage is minimal.
The possibilities are endless, it's up to your imagination.
But you can have fun with it too, the Rookie is very sensitive to thermals and you can "dial in" even very weak thermal "climbs" low to the ground.

We wish you a lot of fun!

Key Features:
Wingspan: 880 mm
Lenght: 730 mm
AUW: 130 g
Servos: 2 x 6g
Akku: 1s 600mAh

Package Includes:
kit with hardware without equipment

Radiostyrd!

The Rookie was designed as an addition to your modeling activities for your children or wives to keep them from getting bored with you on the field.

They can just throw it around like a thrower and when they get bored you give them the transmitter.
For example, you can mark out the landing area and the take-off line on the pad for them.
Or you can tow them behind almost any epp model 1 to 3 at a time.
They can then compete to see who lands last.
During the tow, the Rookie doesn't have to steer at all, just disengage by fully pulling the elevator when altitude is reached.
Don't have a suitable model for towing at hand? No problem, the Rookie is easily towed on a rubber band folded
made of about 5m of 3x1 rubber and 20-30m of Kevlar thread (silon) finished with a ring (for keys).
And now you have time to work on your own model, because with the Rokkie model you don't have to worry about letting
to fly anyone without your supervision. Due to its extra light weight and stability, the risk of damage is minimal.
The possibilities are endless, it's up to your imagination.
But you can have fun with it too, the Rookie is very sensitive to thermals and you can "dial in" even very weak thermal "climbs" low to the ground.

We wish you a lot of fun!

Key Features:
Wingspan: 880 mm
Lenght: 730 mm
AUW: 130 g
Servos: 2 x 6g
Akku: 1s 600mAh

Package Includes:
kit with hardware without equipment

Radiostyrd!

The Rookie was designed as an addition to your modeling activities for your children or wives to keep them from getting bored with you on the field.

They can just throw it around like a thrower and when they get bored you give them the transmitter.
For example, you can mark out the landing area and the take-off line on the pad for them.
Or you can tow them behind almost any epp model 1 to 3 at a time.
They can then compete to see who lands last.
During the tow, the Rookie doesn't have to steer at all, just disengage by fully pulling the elevator when altitude is reached.
Don't have a suitable model for towing at hand? No problem, the Rookie is easily towed on a rubber band folded
made of about 5m of 3x1 rubber and 20-30m of Kevlar thread (silon) finished with a ring (for keys).
And now you have time to work on your own model, because with the Rokkie model you don't have to worry about letting
to fly anyone without your supervision. Due to its extra light weight and stability, the risk of damage is minimal.
The possibilities are endless, it's up to your imagination.
But you can have fun with it too, the Rookie is very sensitive to thermals and you can "dial in" even very weak thermal "climbs" low to the ground.

We wish you a lot of fun!

Key Features:
Wingspan: 880 mm
Lenght: 730 mm
AUW: 130 g
Servos: 2 x 6g
Akku: 1s 600mAh

Package Includes:
kit with hardware without equipment

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Köp till:
Radiosändare+mottagare,
Lipo-acc (Ex.Tattu 1550-3S, Tattu 1800-3S LiPo)
LiPo-laddare.
Kablar o kontakter som passar.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Köp till:
Radiosändare+mottagare,
Lipo-acc (Ex.Tattu 1550-3S, Tattu 1800-3S LiPo)
LiPo-laddare.
Kablar o kontakter som passar.

A very popular category for us is the XL. All XL size aircraft have very advanced flight characteristics already, inertia like a construction aircraft and yet it is still made of EPP which is almost unbreakable in these dimensions. This gives the pilot the opportunity to learn all the autorotation figures without worrying about destroying his model.

An incredible advantage of this design is its resistance to mechanical damage while being resistant to inclement weather. The Laser XL has a flying weight of just under 800g, meaning that even winds of greater force are hardly noticeable on the model.

After many tests, we have proven a completely new wing concept in this category. At the fuselage the wing is glued with its whole contact area to the spine, this makes the model even stronger and at the same time due to the balancing flap at the end of the aileron the model is more controllable and at the same time the load on the servo is slightly reduced.

This time there is no fully-moving elevator on the model, due to maintaining the highest durability. The Laser XL is still very maneuverable over the elevator, due to the correct layout of the model surfaces.

Key Features
wingspan: 1060 mm
lenght: 1120 mm
flight weight: 750 - 820 g
engine: 100 - 120g
controller: 40-50A / 4s
servos: 4x 14 - 18g
battery: 3s - 4s 1300 - 1800mAh
propeller: 10 - 11 inches

A very popular category for us is the XL. All XL size aircraft have very advanced flight characteristics already, inertia like a construction aircraft and yet it is still made of EPP which is almost unbreakable in these dimensions. This gives the pilot the opportunity to learn all the autorotation figures without worrying about destroying his model.

An incredible advantage of this design is its resistance to mechanical damage while being resistant to inclement weather. The Laser XL has a flying weight of just under 800g, meaning that even winds of greater force are hardly noticeable on the model.

After many tests, we have proven a completely new wing concept in this category. At the fuselage the wing is glued with its whole contact area to the spine, this makes the model even stronger and at the same time due to the balancing flap at the end of the aileron the model is more controllable and at the same time the load on the servo is slightly reduced.

This time there is no fully-moving elevator on the model, due to maintaining the highest durability. The Laser XL is still very maneuverable over the elevator, due to the correct layout of the model surfaces.

Key Features
wingspan: 1060 mm
lenght: 1120 mm
flight weight: 750 - 820 g
engine: 100 - 120g
controller: 40-50A / 4s
servos: 4x 14 - 18g
battery: 3s - 4s 1300 - 1800mAh
propeller: 10 - 11 inches

COMBO Erbjudande!

RC Factory LASER 200

OBS! Setupen är i första hand avsedd för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

Vi skickar med 20A reglage, gör att det går bra att även använda 3S lipo.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Höjd: 80 mm till hjulaxel.
Bredd: ca 190 mm
Tjocklek: ca.1.3 till 1.6  mm.
Vikt: 8 g.

Kan naturligtvis användas till andra flygplan i samma viktklass.

Höjd: 120 mm till hjulaxel.
Bredd: ca 235 mm
Tjocklek: ca.1.6 mm.
Vikt: 14 g.

Kan naturligtvis användas till andra flygplan i samma viktklass.

Strong neodymium magnets suitable for mounting some parts of the model.

Key Features:
Diameter: 8 mm
Thickness: 2 mm
Weight: 0.75 g

Package Includes:
6x Magnet

Strong neodymium magnets suitable for mounting some parts of a model.

Key Features:
Diameter: 5 mm
Thickness: 2 mm
Weight: 0.3 g

Package Includes:
6x Magnet

Threaded terminal with M2 thread and internal hole with a diameter of 1.5 mm.

Key Features:
Thread: M2
Inner diameter: 1.5mm
Thread length: 8mm
Overall length: 19mm
Weight: 0.3g

Package Includes:
10x Threaded terminal

Threaded terminal with M2 thread and internal hole with a diameter of 1 mm.

Key Features:
Thread: M2
Inner diameter: 1mm
Thread length: 8mm
Overall length: 19mm
Weight: 0.3g

Package Includes:
10x Threaded terminal

MPJET terminator with ball link + screw

För limmning av max.1.5 mm kolfiberstång. (ej gängning).

Key Features:
Weight: 0.2g

Package Includes:
10x Terminator
10x screw

Very light terminator for attaching a servo lever made, especially for RC Factory.
The terminator has a groove for easy installation of the carbon rod.

Key Features:
Weight: 0.03g
Groove length: 10mm

Package Includes:
10x Terminator

RC Factory Laser 200

In cooperation with Jan Votava we have created a new indoor plane, which we like to call "Gamechanger"

Wingspan: 855mm
Lenght: 935mm
AUW: 155-170g
Motor: 2204 1800-2300kv
ESC: 15A / 16A 4D
Servos: 1x 9-12g, 2x 6-10g
Battery: 300-450mAh 2/3S
Propeller: 8x4.1

Package Includes:
Kit is with hardware , without equipment set.  

RC Factory Storm.

The wing with a traction engine was created as a successor of many years tested models created by Jan Špatný. The wing is much more stable and better controllable than the wing with motor on the tail.

The Storm's small fuselage design is ready for complete hiding of electronics in the fuselage, which makes the model more elegant. The advantage of the wing is stability even in very slow flight, but at the same time very calm in light winds.

The model also meets the rules of indoor pylon racing - RCHP

Key Features:
Wingspan: 650 mm
Length: 250 mm
AUW: 110-130 g
Motor: 2202 - 2204
Regulator: 15A
Servo: 2 x 6g
Battery: 2s 350mAh
Propeller: 5"

Innehåll:
Endast modell och smådelar, såsom roderstänger/horn mm
Köp till elektroniken rekommenderad nedan.
Limmas med vanligt CA-Lim (+ Aktivatorspray) Alt. UHU-POR.

RC Factory Storm.

The wing with a traction engine was created as a successor of many years tested models created by Jan Špatný. The wing is much more stable and better controllable than the wing with motor on the tail.

The Storm's small fuselage design is ready for complete hiding of electronics in the fuselage, which makes the model more elegant. The advantage of the wing is stability even in very slow flight, but at the same time very calm in light winds.

The model also meets the rules of indoor pylon racing - RCHP

Key Features:
Wingspan: 650 mm
Length: 250 mm
AUW: 110-130 g
Motor: 2202 - 2204
Regulator: 15A
Servo: 2 x 6g
Battery: 2s 350mAh
Propeller: 5"

Innehåll:
Endast modell och smådelar, såsom roderstänger/horn mm
Köp till elektroniken rekommenderad nedan.
Limmas med vanligt CA-Lim (+ Aktivatorspray) Alt. UHU-POR.

RC Factory Storm.

The wing with a traction engine was created as a successor of many years tested models created by Jan Špatný. The wing is much more stable and better controllable than the wing with motor on the tail.

The Storm's small fuselage design is ready for complete hiding of electronics in the fuselage, which makes the model more elegant. The advantage of the wing is stability even in very slow flight, but at the same time very calm in light winds.

The model also meets the rules of indoor pylon racing - RCHP

Key Features:
Wingspan: 650 mm
Length: 250 mm
AUW: 110-130 g
Motor: 2202 - 2204
Regulator: 15A
Servo: 2 x 6g
Battery: 2s 350mAh
Propeller: 5"

Innehåll:
Endast modell och smådelar, såsom roderstänger/horn mm
Köp till elektroniken rekommenderad nedan.
Limmas med vanligt CA-Lim (+ Aktivatorspray) Alt. UHU-POR.

The Step 2 model was designed by Jan Sedlacek as a successor to the Step One model, especially for beginners of RC flying, but also for the fun of the more experienced ones.

The construction is in standard EPP thickness, so Step Two is durable and almost unbreakable. We have tried to simplify the assembly of the model as much as possible, so that even an inexperienced modeler can build the model correctly and without complications. This is also the basis for the very detailed instructions.
If the recommended settings are followed, Step 2 is easy to operate. The model is calm and stable in the air, but choose a windless air for the first launches.
The easily removable wing makes transport easy even when travelling for example on holiday. The Step Two comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can also take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.
The equipment for the model is selected so that the complete equipment from the Step One can be used, only two Volta D6M aileron servos are needed



Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 1140 mm
Length: 830 mm
AUW: 350 g

Tillval (medföljer ej):
Motor: 2204 - 2206
ESC: 15A
Servo: 4 x 6g
Battery: 450 3S, 600 2S (25C)
Propeller: 8x4.1

The Step 2 model was designed by Jan Sedlacek as a successor to the Step One model, especially for beginners of RC flying, but also for the fun of the more experienced ones.

The construction is in standard EPP thickness, so Step Two is durable and almost unbreakable. We have tried to simplify the assembly of the model as much as possible, so that even an inexperienced modeler can build the model correctly and without complications. This is also the basis for the very detailed instructions.
If the recommended settings are followed, Step 2 is easy to operate. The model is calm and stable in the air, but choose a windless air for the first launches.
The easily removable wing makes transport easy even when travelling for example on holiday. The Step Two comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can also take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.
The equipment for the model is selected so that the complete equipment from the Step One can be used, only two Volta D6M aileron servos are needed


Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 1140 mm
Length: 830 mm
AUW: 350 g

Tillval (medföljer ej):
Motor: 2204 - 2206
ESC: 15A
Servo: 4 x 6g
Battery: 450 3S, 600 2S (25C)
Propeller: 8x4.1

The Step 2 model was designed by Jan Sedlacek as a successor to the Step One model, especially for beginners of RC flying, but also for the fun of the more experienced ones.

The construction is in standard EPP thickness, so Step Two is durable and almost unbreakable. We have tried to simplify the assembly of the model as much as possible, so that even an inexperienced modeler can build the model correctly and without complications. This is also the basis for the very detailed instructions.
If the recommended settings are followed, Step 2 is easy to operate. The model is calm and stable in the air, but choose a windless air for the first launches.
The easily removable wing makes transport easy even when travelling for example on holiday. The Step Two comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can also take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.
The equipment for the model is selected so that the complete equipment from the Step One can be used, only two Volta D6M aileron servos are needed


Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 1140 mm
Length: 830 mm
AUW: 350 g

Tillval (medföljer ej):
Motor: 2204 - 2206
ESC: 15A
Servo: 4 x 6g
Battery: 450 3S, 600 2S (25C)
Propeller: 8x4.1

The Step 2 model was designed by Jan Sedlacek as a successor to the Step One model, especially for beginners of RC flying, but also for the fun of the more experienced ones.

The construction is in standard EPP thickness, so Step Two is durable and almost unbreakable. We have tried to simplify the assembly of the model as much as possible, so that even an inexperienced modeler can build the model correctly and without complications. This is also the basis for the very detailed instructions.
If the recommended settings are followed, Step 2 is easy to operate. The model is calm and stable in the air, but choose a windless air for the first launches.
The easily removable wing makes transport easy even when travelling for example on holiday. The Step Two comes with a carbon landing gear, so you can practice take-offs and landings from the ground. Due to the large wheels, you can also take off from mown grass. Take-offs and landings should always be made into the wind, as the airspeed relative to the ground will be reduced and you will therefore need less space for take-off and landing. Avoid flying near high tension wires and always remember that even with such a simple model, damage to property or health can easily occur.
The equipment for the model is selected so that the complete equipment from the Step One can be used, only two Volta D6M aileron servos are needed


Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 1140 mm
Length: 830 mm
AUW: 350 g

Tillval (medföljer ej):
Motor: 2204 - 2206
ESC: 15A
Servo: 4 x 6g
Battery: 450 3S, 600 2S (25C)
Propeller: 8x4.1

Quality strap for hanging the RC radio on the neck. There is a comfortable padding on the strap, thanks to which the strap does not push or cut. The length of the strap is adjustable with two buckles. You attach the strap to the radio with a carabiner. The part on the transmitter can then be easily unclipped.

Key Features
Minimum length: 50cm
Maximum length: 65cm
Width: 20-31mm
Comfortable padding

The Cap 10 model was designed in collaboration with team pilot Jan Votava, directly according to his requirements for flight characteristics. Now We are happy to offer you the final version, which Us and Jan Votava are completely satisfied. We managed to create an EPP 3D model with great extreme flight characteristics.
 It was designed for pilots, who just started with 3D acrobatics and experienced 3D pilots, who want to fly in a small places.
Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features:
Wingspan: 810 mm
Lenght: 780 mm
AUW: 210 - 230 g

Package Includes:
Kit including landing gear and hardware , without equipment set.

The Cap 10 model was designed in collaboration with team pilot Jan Votava, directly according to his requirements for flight characteristics. Now We are happy to offer you the final version, which Us and Jan Votava are completely satisfied. We managed to create an EPP 3D model with great extreme flight characteristics.
 It was designed for pilots, who just started with 3D acrobatics and experienced 3D pilots, who want to fly in a small places.
Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features:
Wingspan: 810 mm
Lenght: 780 mm
AUW: 210 - 230 g

Package Includes:
Kit including landing gear and hardware , without equipment set.

The Bücker Jungmeister was designed for beginners and experienced 3D pilots who want to fly in a small space. The advantage of the construction is the speed with which you can build the model - and also the considerable resistance to damage. The aircraft has a fully floating elevator that gives the aircraft incredible maneuverability. The model has fully functional landing gear, so it adds authenticity to the flight even when taxiing on the ground.

Backyard series:
The original line of 3D models suitable for small space flying is characterized by its high structural durability. You can learn new 3D turns without fear of destroying your model.

Key Features:

Breite: 775 mm
Länge: 875 mm
AUW: 210 - 230 g

Package Includes:
Kit including carbon landing gear, Hardware , without equipment set - see photo

The Bücker Jungmeister was designed for beginners and experienced 3D pilots who want to fly in a small space. The advantage of the construction is the speed with which you can build the model - and also the considerable resistance to damage. The aircraft has a fully floating elevator that gives the aircraft incredible maneuverability. The model has fully functional landing gear, so it adds authenticity to the flight even when taxiing on the ground.

Backyard series:
The original line of 3D models suitable for small space flying is characterized by its high structural durability. You can learn new 3D turns without fear of destroying your model.

Key Features:

Breite: 775 mm
Länge: 875 mm
AUW: 210 - 230 g

Package Includes:
Kit including carbon landing gear, Hardware , without equipment set - see photo

Borstlös motor passande till Ex. RCFactorys motorgondol (Termik).

Size: 1806
Kv: 2280
Shaft: M5
Dimensions: diam. 23 × 16 mm
Weight: 18.6g

Package Includes:
1x Motor
1x Set of screws

Rek, fartreglage: Hobbywing Flyfun 20A.
Prop: Se data bild 2.

Air Truck was firstly designed as a plane to tow the Stigra glider. Given it's great power and flight charasteristics, it can eventually tow any glider of up to some 1.2 kg AUW. The V-tail may look surprising on such plane but it is best for towing, obviously - the tow line is routed between the V planes and doesn't bother the pilot by interfering with the rudder. The plane is very predictable, so that even less experienced pilots can tow gliders for the first time, without worries.

The plane was designed by the electric pylon racing world champion Jan Sedlacek. Hence the idea to use it in fun pylon races! Air Truck racing is actually becoming a thing in the Czech republic. For faster flight, more durability or racing, you can cover the plane in 38 micron iron-on film (available on this eshop too).

The wings are removable, attached by two plastic screws. The disassembled plane is easy to transport. Decent size of the fuselage means you can easily hide all the electronic parts inside. The battery bay cover lid is held in place by magnets so that you can change the battery fast and easily.

Air Truck was also designed as a docile aileron trainer - just limit the control throws to some 20 degress or less.

Key Features:
wingspan: 1050 mm
length: 950 mm
AUW: 600g+
motor: 100 - 120 g outrunner
ESC: 35 - 45 A / 4s
servos: 2 st EMax ES09MA och 2 st EMax ES3004MA
battery: 3s - 4s 1300 - 1800 mAh
propeller: 10 - 11"

Package Includes:
Kit including landing gear and hardware, without equipment set

Our first biplane in the XL line.

För flygning såväl utomhus som inomhus! Se video under fliken "Videos" !

Together with our partner company Twisted Hobbys and their associate designer Cody Wojcik, we have built upon our accumulated experience and created this revolutionary bipe with full flying stabilizer. Here comes the craziest bipe in the 1 m category, period. Extreme agility with that special "bipe feel". Yet still, with limited throws, the plane is docile enough to become a well behaved 3D training model.

Key Features:
wingspan: 1000 mm
lenght: 1030 mm
AUW: 750 - 800 g
motor: 2814/1000kv
ESC: 45A / 3-4s
servos: 4x Volta D14
battery:  3s - 4s 1300 - 1800 mAh
propeller: 10 - 11 tum

Package Includes:
Kit including landing gear, without equipment set

Our first biplane in the XL line.

För flygning såväl utomhus som inomhus! Se video under fliken "Videos" !

Together with our partner company Twisted Hobbys and their associate designer Cody Wojcik, we have built upon our accumulated experience and created this revolutionary bipe with full flying stabilizer. Here comes the craziest bipe in the 1 m category, period. Extreme agility with that special "bipe feel". Yet still, with limited throws, the plane is docile enough to become a well behaved 3D training model.

Key Features:
wingspan: 1000 mm
lenght: 1030 mm
AUW: 750 - 800 g
motor: 2814/1000kv
ESC: 45A / 3-4s
servos: 4x Volta D14
battery:  3s - 4s 1300 - 1800 mAh
propeller: 10 - 11 tum

Package Includes:
Kit including landing gear, without equipment set

Termik PRO is our first exclusively thermal glider, capable of air towing, slope soaring or bungee/fishing line start. Great and predictable flying qualities. The plane is covered in 38 micron laminating film, which gives it better performance than what you see in "raw foam" models.

- For air towing, e.g. via our Air Truck, you have an integrated tow release system.
- For bungee start, the model features a tow hook.

The canopy is removable, held with in place with a plastic hook and a magnet. Inside there is enough space for all the RC equipment. The fuselage is pre-built from the factory.

Termik PRO is controlled via ailerons, rudder and elevator. If you prefer rudder only, choose the Termik.

Key Features:
wingspan: 1440mm
length: 960mm
AUW: 400-450g

Package Includes:
Kit without equipment

Ladda ner byggbeskrivningen under fliken "Dokument"!
Klädsel plastfilm, se nedan på rekommenderade tillbehör.

Termik PRO is our first exclusively thermal glider, capable of air towing, slope soaring or bungee/fishing line start. Great and predictable flying qualities. The plane is covered in 38 micron laminating film, which gives it better performance than what you see in "raw foam" models.

- For air towing, e.g. via our Air Truck, you have an integrated tow release system.
- For bungee start, the model features a tow hook.

The canopy is removable, held with in place with a plastic hook and a magnet. Inside there is enough space for all the RC equipment. The fuselage is pre-built from the factory.

Termik PRO is controlled via ailerons, rudder and elevator. If you prefer rudder only, choose the Termik.

Key Features:
wingspan: 1440mm
length: 960mm
AUW: 400-450g

Package Includes:
Kit without equipment

Ladda ner byggbeskrivningen under fliken "Dokument"!
Klädsel plastfilm, se nedan på rekommenderade tillbehör.

Termik is our first exclusively thermal glider, capable of air towing, slope soaring or bungee/fishing line start. Great and predictable flying qualities. The plane is covered in 38 micron laminating film, which gives it better performance than what you see in "raw foam" models.

- For air towing, e.g. via our Air Truck, you have an integrated tow release system.
- For bungee start, the model features a tow hook.

The canopy is removable, held with in place with a plastic hook and a magnet. Inside there is enough space for all the RC equipment. The fuselage is pre-built from the factory.

Termik is controlled via rudder and elevator.
If you prefer ailerons, choose the Termik PRO, available in two color variants.

Key Features:
wingspan: 1440 mm
length:  960 mm
AUW: 400 - 450 g

Package Includes:
Kit without equipment

Ladda ner byggbeskrivningen under fliken "Dokument"!
Klädsel plastfilm, se nedan på rekommenderade tillbehör.

Synergy was designed by team pilot Jan Votava, who wanted to use all his experience from the F3A category and put it into this model. Synergy is designed for all pilots who like precise flying, precisely made rolls, flips, but also demanding maneuvers , so that this model can be a competitive plane for F3P class. The narrower wings and smaller area at the end are balanced by larger canalyzers. The model has a very predictable and linear response in all flight positions. Thanks to this the ability to fly slowly and calmly, it is the ideal first model for the hall, even if you do not dare to do acrobatics yet.

Key Features
Wingspan: 845 mm
Lenght: 945 mm
AUW: 105-130 g
Motor: 40 - 60 W
ESC: 5 - 15 A
Servos: 3x 4,5 - 6g
Battery: 180 - 350 2S
Propeller: 9 x 2.8 - 9 x 3.8, 8 x 4

SUPER EXTRA LIMITED EDITION! only 100 pieces!

For the start of the new indoor season, we have created a limited edition of our indoor special - Super Extra

This Super Extra is our most revolutionary model so far. Designed by Jan Votava and Jan Sedlacek in close cooperation, the focus was both on flight characteristics and structural rigidity. The airframe is both strong and precise, to withstand these violent manoeuvres this plane is capable of.

Monster ailerons, reinforced for torsion rigidity, allow for unprecedented roll rate. Full flying stab, not often seen in this indoor category, allows for extreme tight "around the CG" loops - or should we rather say flips? All the above makes this plane unique and we dare say one of the most attractive ones we made so far.

With limited control throws, to ca 30 degrees according to pilot skills, the plane is still well behaved and predictable.

Key Features:
Wingspan: 865mm
Lenght: 930mm
AUW: 165-185g
2204-2206 2300kv motor
15A ESC
1x 14g 2x 8-10g servos
2s 300-450mAh battery

Air Truck was firstly designed as a plane to tow the Stigra glider. Given it's great power and flight charasteristics, it can eventually tow any glider of up to some 1.2 kg AUW. The V-tail may look surprising on such plane but it is best for towing, obviously - the tow line is routed between the V planes and doesn't bother the pilot by interfering with the rudder. The plane is very predictable, so that even less experienced pilots can tow gliders for the first time, without worries.

The plane was designed by the electric pylon racing world champion Jan Sedlacek. Hence the idea to use it in fun pylon races! Air Truck racing is actually becoming a thing in the Czech republic. For faster flight, more durability or racing, you can cover the plane in 38 micron iron-on film (available on this eshop too).

The wings are removable, attached by two plastic screws. The disassembled plane is easy to transport. Decent size of the fuselage means you can easily hide all the electronic parts inside. The battery bay cover lid is held in place by magnets so that you can change the battery fast and easily.

Air Truck was also designed as a docile aileron trainer - just limit the control throws to some 20 degress or less.

Key Features:
wingspan: 1050 mm
length: 950 mm
AUW: 600g+
motor: 100 - 120 g outrunner
ESC: 35 - 45 A / 4s
servos: 2 st EMax ES09MA och 2 st EMax ES3004MA
battery: 3s - 4s 1300 - 1800 mAh
propeller: 10 - 11"

Package Includes:
Kit including landing gear and hardware, without equipment set

Air Truck was firstly designed as a plane to tow the Stigra glider. Given it's great power and flight charasteristics, it can eventually tow any glider of up to some 1.2 kg AUW. The V-tail may look surprising on such plane but it is best for towing, obviously - the tow line is routed between the V planes and doesn't bother the pilot by interfering with the rudder. The plane is very predictable, so that even less experienced pilots can tow gliders for the first time, without worries.

The plane was designed by the electric pylon racing world champion Jan Sedlacek. Hence the idea to use it in fun pylon races! Air Truck racing is actually becoming a thing in the Czech republic. For faster flight, more durability or racing, you can cover the plane in 38 micron iron-on film (available on this eshop too).

The wings are removable, attached by two plastic screws. The disassembled plane is easy to transport. Decent size of the fuselage means you can easily hide all the electronic parts inside. The battery bay cover lid is held in place by magnets so that you can change the battery fast and easily.

Air Truck was also designed as a docile aileron trainer - just limit the control throws to some 20 degress or less.

Key Features:
wingspan: 1050 mm
length: 950 mm
AUW: 600g+
motor: 100 - 120 g outrunner
ESC: 35 - 45 A / 4s
servos: 2 st EMax ES09MA och 2 st EMax ES3004MA
battery: 3s - 4s 1300 - 1800 mAh
propeller: 10 - 11"

Package Includes:
Kit including landing gear and hardware, without equipment set

Air Truck was firstly designed as a plane to tow the Stigra glider. Given it's great power and flight charasteristics, it can eventually tow any glider of up to some 1.2 kg AUW. The V-tail may look surprising on such plane but it is best for towing, obviously - the tow line is routed between the V planes and doesn't bother the pilot by interfering with the rudder. The plane is very predictable, so that even less experienced pilots can tow gliders for the first time, without worries.

The plane was designed by the electric pylon racing world champion Jan Sedlacek. Hence the idea to use it in fun pylon races! Air Truck racing is actually becoming a thing in the Czech republic. For faster flight, more durability or racing, you can cover the plane in 38 micron iron-on film (available on this eshop too).

The wings are removable, attached by two plastic screws. The disassembled plane is easy to transport. Decent size of the fuselage means you can easily hide all the electronic parts inside. The battery bay cover lid is held in place by magnets so that you can change the battery fast and easily.

Air Truck was also designed as a docile aileron trainer - just limit the control throws to some 20 degress or less.

Key Features:
wingspan: 1050 mm
length: 950 mm
AUW: 600g+
motor: 100 - 120 g outrunner
ESC: 35 - 45 A / 4s
servos: 2 st EMax ES09MA och 2 st EMax ES3004MA
battery: 3s - 4s 1300 - 1800 mAh
propeller: 10 - 11"

Package Includes:
Kit including landing gear and hardware, without equipment set

Stigra is our first production glider, based on our extensive experience in aerobatic and slope flying. Stigra has incredible flying characteristics, thanks to oversized ailerons and full flying stab with up to + - 90 degree throws. We suggest using several flight conditions: with lower throws, it is a steady and predictable model capable even of thermal soaring in good lift conditions. With full throws, this is indeed the wildest glider you have ever seen.

The wings are easily removable and locked in place with the help of magnets. You need no tools to assemble the model. The canopy is easily removable, fixed with a plastic tab and again, magnets. There is enough space for all the necessary electronics inside the canopy.

There is one more unique thing about this model: the tow system. The model can be towed by another (powered) model, where the Air Truck was especially designed for this task (besides other things). You release the tow line by a short full deflection of the rudder and the fun may begin.

Key Features:
wingspan: 1200mm
lenght: 910mm
AUW: 400-650g
Servos: 4 st EMax ES09MA alt. ES09MD
Acc: 2s 600-1000mAh

Package Includes:
Kit including landing gear and hardware, without equipment set

Stigra is our first production glider, based on our extensive experience in aerobatic and slope flying. Stigra has incredible flying characteristics, thanks to oversized ailerons and full flying stab with up to + - 90 degree throws. We suggest using several flight conditions: with lower throws, it is a steady and predictable model capable even of thermal soaring in good lift conditions. With full throws, this is indeed the wildest glider you have ever seen.

The wings are easily removable and locked in place with the help of magnets. You need no tools to assemble the model. The canopy is easily removable, fixed with a plastic tab and again, magnets. There is enough space for all the necessary electronics inside the canopy.

There is one more unique thing about this model: the tow system. The model can be towed by another (powered) model, where the Air Truck was especially designed for this task (besides other things). You release the tow line by a short full deflection of the rudder and the fun may begin.

Key Features:
wingspan: 1200mm
lenght: 910mm
AUW: 400-650g
Servos: 4 st EMax ES09MA alt. ES09MD
Acc: 2s 600-1000mAh

Package Includes:
Kit including landing gear and hardware, without equipment set

Stigra is our first production glider, based on our extensive experience in aerobatic and slope flying. Stigra has incredible flying characteristics, thanks to oversized ailerons and full flying stab with up to + - 90 degree throws. We suggest using several flight conditions: with lower throws, it is a steady and predictable model capable even of thermal soaring in good lift conditions. With full throws, this is indeed the wildest glider you have ever seen.

The wings are easily removable and locked in place with the help of magnets. You need no tools to assemble the model. The canopy is easily removable, fixed with a plastic tab and again, magnets. There is enough space for all the necessary electronics inside the canopy.

There is one more unique thing about this model: the tow system. The model can be towed by another (powered) model, where the Air Truck was especially designed for this task (besides other things). You release the tow line by a short full deflection of the rudder and the fun may begin.

Key Features:
wingspan: 1200mm
lenght: 910mm
AUW: 400-650g
Servos: 4 st EMax ES09MA alt. ES09MD
Acc: 2s 600-1000mAh

Package Includes:
Kit including landing gear and hardware, without equipment set

The Big Super Extra is the successor to our successful Edge 540 V3. We paid attention to the details to move this plane to the step forward again.

This is a first model of a new line of 1m wingspan EPP models with increased stiffness and torsion rigidity. We have beefed up everything, but especially the torsion rigidity of the fuselage - so that fuselage twist in fast rolling maneuvers is now totally a thing of the past. The wing is thicker too, for better tolerance of the most insane, high-G stunts.

This model can also take a bigger motor up to the 2217 size, although it already flies nicely with 2212 motors. If you prefer insane power in your 3D models, this one is the ticket.

Outdoor Series:

If you prefer bigger models with fully airfoiled wing, you can´t make a mistake with these. Developed by some of the best 3D pilots for a combination of 3D capability and easy, predictable handling.

Key Features:
Wing span: 1000 mm
Length: 1030 mm
Weight: ca 500g depending on the equipment used

Passande delar (ingår ej!):
Motor: 2212 - 2217, 150 - 200W
Servos: 4x 9 - 15g
Receiver: micro, mini
ESC: 25-35A.
Battery pack: 3s 1000 - 1500 mAh
Proppeller: 10x4.6 APC

Package Includes:
Kit including carbon landing gear, hardware, without equipment set

The Big Super Extra is the successor to our successful Edge 540 V3. We paid attention to the details to move this plane to the step forward again.

This is a first model of a new line of 1m wingspan EPP models with increased stiffness and torsion rigidity. We have beefed up everything, but especially the torsion rigidity of the fuselage - so that fuselage twist in fast rolling maneuvers is now totally a thing of the past. The wing is thicker too, for better tolerance of the most insane, high-G stunts.

This model can also take a bigger motor up to the 2217 size, although it already flies nicely with 2212 motors. If you prefer insane power in your 3D models, this one is the ticket.

Outdoor Series:

If you prefer bigger models with fully airfoiled wing, you can´t make a mistake with these. Developed by some of the best 3D pilots for a combination of 3D capability and easy, predictable handling.

Key Features:
Wing span: 1000 mm
Length: 1030 mm
Weight: ca 500g depending on the equipment used

Passande delar (ingår ej!):
Motor: 2212 - 2217, 150 - 200W
Servos: 4x 9 - 15g
Receiver: micro, mini
ESC: 25-35A.
Battery pack: 3s 1000 - 1500 mAh
Proppeller: 10x4.6 APC

Package Includes:
Kit including carbon landing gear, hardware, without equipment set

RC Factory Edge XL

Se film under fliken "Videos"!!


Vingspann: 1060 mm.
Kroppslängd: 1120 mm
Flygvikt: 680 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Edge XL
Go insane! From the realm of "flies like balsa, costs and repairs like foam" arrived a new plane, the Edge XL.
 
Loosely based on the full size Edge, the unmatched Red Bull Air Race (TM) competitor, the designer's goal was to make something that flies at least as good as the legendary Cody Wojcik's Veloxity while having somewhat different looks. You be the judge how well RC Factory managed to achieve this goal.
 
The early testers' response is extremely encouraging: Jan Votava, junior European F3A champion and World vice-champion, who was originally quite skeptical about this size of models, admitted that he never expected anything like that - yet now he is jumping up and down with excitement. "Everybody is going to love this" was his verdict, just as he never bothered with 3s and loaded the plane with his 1500 mAh, 4s copter battery pack rated at 95C. "The plane goes ballistic and there is nothing it can't do", says Votava.
 
Insane roll rate, great linear response to all controls, whip-like snap rolls, very steady hover, smooth performance on low rates but total madness on high ones. If you are looking for an insane piece of equipment to wow your friends, look no further.

This Super Extra is our most revolutionary model so far. Designed by Jan Votava and Jan Sedlacek in close cooperation, the focus was both on flight characteristics and structural rigidity.

The airframe is both strong and precise, to withstand these violent manoeuvres this plane is capable of.

Monster ailerons, reinforced for torsion rigidity,  allow for unprecedented roll rate. Full flying stab, not often seen in this indoor category, allows for extreme tight "around the CG" loops - or should we rather say flips? All the above makes this plane unique and we dare say one of the most attractive ones we made so far.

With limited control throws, to ca 30 degrees according to pilot skills, the plane is still well behaved and predictable.

Key Features:
Wingspan: 865mm
Lenght: 930mm
AUW: 165-185g
2204-2206 2300kv motor
15A ESC
1x 14g 2x 8-10g servos
2s 300-450mAh battery
micro reciever
8x4.1 propeller

This Super Extra is our most revolutionary model so far. Designed by Jan Votava and Jan Sedlacek in close cooperation, the focus was both on flight characteristics and structural rigidity. The airframe is both strong and precise, to withstand these violent manoeuvres this plane is capable of.

Monster ailerons, reinforced for torsion rigidity,  allow for unprecedented roll rate. Full flying stab, not often seen in this indoor category, allows for extreme tight "around the CG" loops - or should we rather say flips? All the above makes this plane unique and we dare say one of the most attractive ones we made so far.

With limited control throws, to ca 30 degrees according to pilot skills, the plane is still well behaved and predictable.

Key Features
Wingspan: 865mm

Lenght: 930mm
AUW: 165-185g
2204-2206 2300kv motor
15A ESC
1x 14g 2x 8-10g servos
2s 300-450mAh battery
micro reciever
8x4.1 propeller

COMBO Erbjudande!

RC Factory Synergy.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Synergy.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Synergy.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Synergy was designed by team pilot Jan Votava, who wanted to use all his experience from the F3A category and put it into this model. Synergy is designed for all pilots who like precise flying, precisely made rolls, flips, but also demanding maneuvers , so that this model can be a competitive plane for F3P class. The narrower wings and smaller area at the end are balanced by larger canalyzers. The model has a very predictable and linear response in all flight positions. Thanks to this the ability to fly slowly and calmly, it is the ideal first model for the hall, even if you do not dare to do acrobatics yet.

Key Features
Wingspan: 845 mm
Lenght: 945 mm
AUW: 110-140 g
Motor: 40 - 60 W
ESC: 5 - 15 A
Servos: 3x 4,5 - 6g
Battery: 180 - 350 2S
Propeller: 9 x 2.8 - 9 x 3.8, 8 x 4

Synergy was designed by team pilot Jan Votava, who wanted to use all his experience from the F3A category and put it into this model. Synergy is designed for all pilots who like precise flying, precisely made rolls, flips, but also demanding maneuvers , so that this model can be a competitive plane for F3P class. The narrower wings and smaller area at the end are balanced by larger canalyzers. The model has a very predictable and linear response in all flight positions. Thanks to this the ability to fly slowly and calmly, it is the ideal first model for the hall, even if you do not dare to do acrobatics yet.

Key Features
Wingspan: 845 mm
Lenght: 945 mm
AUW: 110-140 g
Motor: 40 - 60 W
ESC: 5 - 15 A
Servos: 3x 4,5 - 6g
Battery: 180 - 350 2S
Propeller: 9 x 2.8 - 9 x 3.8, 8 x 4

Synergy was designed by team pilot Jan Votava, who wanted to use all his experience from the F3A category and put it into this model. Synergy is designed for all pilots who like precise flying, precisely made rolls, flips, but also demanding maneuvers , so that this model can be a competitive plane for F3P class. The narrower wings and smaller area at the end are balanced by larger canalyzers. The model has a very predictable and linear response in all flight positions. Thanks to this the ability to fly slowly and calmly, it is the ideal first model for the hall, even if you do not dare to do acrobatics yet.

Key Features
Wingspan: 845 mm
Lenght: 945 mm
AUW: 110-140 g
Motor: 40 - 60 W
ESC: 5 - 15 A
Servos: 3x 4,5 - 6g
Battery: 180 - 350 2S
Propeller: 9 x 2.8 - 9 x 3.8, 8 x 4

Landställ i kolfiber till RCFactory med 1.2 m i spännvidd.

Veloxity ver. 2.0
Edge XL ver. 2.0
Crack Yak XL

Kan naturligtvis användas till andra flygplan i samma viktklass.

Höjd: 165 mm till hjulaxel.
Bredd: ca 290 mm
Tjocklek: ca. 1.7 mm.
Vikt: 26 g.

Utrustningspaket till RCFactorys Step One Baby.

Ingår:
2 st Motorer
2 st Fartreglage
Propellrar
Servokabel (för anslutning fartreglage, lödning krävs).

The Step One BABY model was designed by Jan Sedlacek, especially for beginners of RC flying, but also for the entertainment of the more experienced pilots.
Baby Step One is powered by only two DC motors, so construction is very quick and easy.
Even with its small dimensions, the model is foldable, so you can take it everywhere with you and you didn't miss it on any trip.
The baby is controlled by dual motors.  The equipment is suitable for any RC kit. One of the variants is also by connecting the motors to the control board from a small drone for home flying. This variant is also very interesting if you have a nonfunctioning drone at home - so this variant was very popular solution for Jan Votava.
Step One BABY is an ideal partner for quiet evenings, in the group of experienced modellers and for complete beginners too.

Motorerna kräver var sin kanal. (Mixas) Styr motorerna istället för roder.

Köp till Utrustningen till Step One Baby (Motor, fartreglage mm). Ingår ej!
Se nedan.

Key Features
wingspan: 500mm
lenght: 415mm
AUW: 35-40g
built in 30 minutes
2x 6/17 brushed motor
2x 1A ESC
2x 30-35mm propellers
1s 180-350mAh

The Yak 55 model was designed in collaboration with team pilot Jan Votava, directly according to his requirements for flight characteristics. Now We are happy to offer you the final version, which Us and Jan Votava are completely satisfied. We managed to create an EPP 3D model with great extreme flight characteristics.
 It was designed for pilots, who just started with 3D acrobatics and experienced 3D pilots, who want to fly in a small places.
Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 800 mm
Lenght: 780 mm
AUW: 220 - 240 g

Package Includes
Kit including landing gear, without equipment set - see photo
Recommended equipment sets (motor, servos, ESC, propeller, batteries) can be found below in accessories.

The Yak 55 model was designed in collaboration with team pilot Jan Votava, directly according to his requirements for flight characteristics. Now We are happy to offer you the final version, which Us and Jan Votava are completely satisfied. We managed to create an EPP 3D model with great extreme flight characteristics.
 It was designed for pilots, who just started with 3D acrobatics and experienced 3D pilots, who want to fly in a small places.
Backyard Series:

This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 800 mm
Lenght: 780 mm
AUW: 220 - 240 g

Package Includes
Kit including landing gear, without equipment set - see photo
Recommended equipment sets (motor, servos, ESC, propeller, batteries) can be found below in accessories.

 The Saab Jas 39 Gripen model was created in two variants - a single-engine version and a twin-engine version.

Kolla in filmen under fliken "Videos" !

The twin-engine version is designed for all 3D acrobatics enthusiasts with the option of flying extreme maneuvers, such as flat splins, knife edge corkscrews or insanely fast twists.

The single-engine version is created with an emphasis on realistic behavior to mimic a real fighter aircraft. Large rudders and 3s powerfull setup makes both versions very agile with excellent flight characteristics.

The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 540 mm
Lenght: 880 mm
AUW: 220 - 250 g

En eller två motorer, välj själv, båda kan byggas med samma modell.
Nedan följer ett förslag på en-motor setup. (vass!).

 The Saab Jas 39 Gripen model was created in two variants - a single-engine version and a twin-engine version.

Kolla in filmen under fliken "Videos" !

The twin-engine version is designed for all 3D acrobatics enthusiasts with the option of flying extreme maneuvers, such as flat splins, knife edge corkscrews or insanely fast twists.

The single-engine version is created with an emphasis on realistic behavior to mimic a real fighter aircraft. Large rudders and 3s powerfull setup makes both versions very agile with excellent flight characteristics.

The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Key Features
Wingspan: 540 mm
Lenght: 880 mm
AUW: 220 - 250 g

En eller två motorer, välj själv, båda kan byggas med samma modell.
Nedan följer ett förslag på en-motor setup. (vass!).

Edge 540 V3 Superlite:
This amazing model is the result of more than 3 years of refining and development by the indoor aerobatic pioneer and World Air Games competitor Jan Spatny. Oversize controls, the right distribution of fuselage side area and side-to-side thrust vectoring give this model some truly unique abilities. Whip-like snap rolls, tight knife edge loops or any other maneuver you can think of, there is nothing this plane couldn't do. Light 4mm EPP construction gives the model flying qualities that are on par with the best milled-out Depron planes, with the added advantage of much better durability. With strengthened aileron hinges, the model is ready for 4D (reverse thrust) flying.

Key Features:
Wing span: 860 mm
Lenght: 920 mm
AUW: 150-180 g
Motor: 60 - 120 W
ESC: 15 A
Servo: 3 x 6g /  1x 9g 2x 6g
Battery: 300-450 2S
Propeller: 8 x 4

Edge 540 V3 Superlite:
This amazing model is the result of more than 3 years of refining and development by the indoor aerobatic pioneer and World Air Games competitor Jan Spatny. Oversize controls, the right distribution of fuselage side area and side-to-side thrust vectoring give this model some truly unique abilities. Whip-like snap rolls, tight knife edge loops or any other maneuver you can think of, there is nothing this plane couldn't do. Light 4mm EPP construction gives the model flying qualities that are on par with the best milled-out Depron planes, with the added advantage of much better durability. With strengthened aileron hinges, the model is ready for 4D (reverse thrust) flying.

Key Features:
Wing span: 860 mm
Lenght: 920 mm
AUW: 150-180 g
Motor: 60 - 120 W
ESC: 15 A
Servo: 3 x 6g /  1x 9g 2x 6g
Battery: 300-450 2S
Propeller: 8 x 4

RC Factory Crack Yak XL Blue-Gold 1080 mm.

Se filmer om hur de byggs o flygs under fliken "Videos" !

The biggest version of the legendary Chris Jewett designed model. With legacy of all the good features of it's predecessors, especially the incredible agility and neutral control response, this model is probably the best one in this size. The full flying stab adds some extra spice to all the possible maneuvers you can fly with it, including loops practically around it's center of gravity.

With tuned down control throws this will be still a smooth and docile 3D trainer for pilots who have just emerged from their beginner phase.

Key Features
wingspan 1080 mm
length 1120 mm
AUW 750 - 850 g
motor 100 - 120 g outrunner
ESC 35 - 45 A / 4s
servos 4x 14 - 18 g
battery 3s - 4s 1300 - 1800 mAh
propeller 10 - 11"
Kit including landing gear, without equipment set - see photo

RC Factory Crack Yak XL  Green-Orange 1080 mm.

Se filmer om hur de byggs o flygs under fliken "Videos" !

The biggest version of the legendary Chris Jewett designed model. With legacy of all the good features of it's predecessors, especially the incredible agility and neutral control response, this model is probably the best one in this size. The full flying stab adds some extra spice to all the possible maneuvers you can fly with it, including loops practically around it's center of gravity.

With tuned down control throws this will be still a smooth and docile 3D trainer for pilots who have just emerged from their beginner phase.

Key Features
wingspan 1080 mm
length 1120 mm
AUW 750 - 850 g
motor 100 - 120 g outrunner
ESC 35 - 45 A / 4s
servos 4x 14 - 18 g
battery 3s - 4s 1300 - 1800 mAh
propeller 10 - 11"
Kit including landing gear, without equipment set - see photo

This model was designed as a game changer in the 1m category. Huge ailerons with unprecedented throws (55 deg) and especially the full flying stab (with practically unlimited throws) will give you such control authority that you really really can't ask for more, ever.

The model is a "scale model" of another model, the unique balsa aerobatic plane Revolto produced by Badan Airplane Kits company. The designer, Dan Bartušek, is known for always coming up with airplanes of recognisable, "sexy" shapes.

You may tune down the control throws for more calm flying style or to learn some basic aerobatics. But we are sure that you will soon itch to increase them to the limits, if only to see what happens.

Key Features
wingspan 1020 mm
length 1030 mm
weight up to 550 g
servos 4 x 10 - 15g
ESC 25A+
motor 2216 or bigger, 2808
battery 3s (850 - 1500 mAh)
Package Includes
The kit with landing gear and all structural parts.

This model was designed as a game changer in the 1m category. Huge ailerons with unprecedented throws (55 deg) and especially the full flying stab (with practically unlimited throws) will give you such control authority that you really really can't ask for more, ever.

The model is a "scale model" of another model, the unique balsa aerobatic plane Revolto produced by Badan Airplane Kits company. The designer, Dan Bartušek, is known for always coming up with airplanes of recognisable, "sexy" shapes.

You may tune down the control throws for more calm flying style or to learn some basic aerobatics. But we are sure that you will soon itch to increase them to the limits, if only to see what happens.

Key Features
wingspan 1020 mm
length 1030 mm
weight up to 550 g
servos 4 x 10 - 15g
ESC 25A+
motor 2216 or bigger, 2808
battery 3s (850 - 1500 mAh)
Package Includes
The kit with landing gear and all structural parts.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Perfekta nybörjarkärran!

Komplettera med radioutrusning, ex. WFLY ET06 och en laddare.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Perfekta nybörjarkärran!

Komplettera med radioutrusning, ex. WFLY ET06 och en laddare.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Perfekta nybörjarkärran!

Komplettera med radioutrusning, ex. WFLY ET06 och en laddare.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Perfekta nybörjarkärran!

Komplettera med radioutrusning, ex. WFLY ET06 och en laddare.

The proXy is a radically new kind of model, designed by Cody Wojcik and Chris Jewett. It combines a "3D foamy" and "FPV drone" categories into one neat package. It can be flown like a simple aileron trainer within line of sight, but you may - and should - also add FPV (first person view) gear to it and fly it virtually "looking out of the cockpit" through tree gaps in your local park or forest.

Massive landing gear was designed for take-offs, landings and touch and go's while still flying FPV. The controls are efficient enough for complete spectrum of aerobatic maneuvers. The pusher configuration keeps your propeller safe and allows for unobstructed view from your FPV camera.

The "avionics tray" has a lot of handy space for your FPV gear, (optional) flight controller and battery.

Key Features
wingspan 1100 mm
length  925 mm
weight 360 g
servos  4 pcs of 9g (Gening D90, Hitec HS-55 etc)
motor 2206 or similar
battery 3s 850 - 1300 mAh
ESC 15A or stronger

Extremely agile model, great for park or backyard flying. Or even a gym. Short fuselage, full flying stab and huge rudder allow for a large envelope of maneuvers, for the delight of experienced 3D pilots. At half - or less - control throws, the model is tame enough for a pilot of intermediate skills. Scale looks, typically shaped cowl and massive, functional landing gear will please every fan of the aviation golden era.

Key Features
wingspan 800 mm
lenth  650 mm
AUW 185 - 210 g

Extremely agile model, great for park or backyard flying. Or even a gym. Short fuselage, full flying stab and huge rudder allow for a large envelope of maneuvers, for the delight of experienced 3D pilots. At half - or less - control throws, the model is tame enough for a pilot of intermediate skills. Scale looks, typically shaped cowl and massive, functional landing gear will please every fan of the aviation golden era.

Key Features
wingspan 800 mm
lenth  650 mm
AUW 185 - 210 g

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Komplettera med LiPo-acc (1800-3S) och radioutrustning.

Specifikation:
Vingspann: 1070 mm.
Kroppslängd: 1120 mm
Flygvikt: ca 550 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Veloxity
 
From the Twisted mind of Cody Wojcik comes the Veloxity! Loosely based on the full-scale Velox Revolution 1, the Veloxity delivers an experience never before available in a foam plane. As one of the stiffest foam airframes around, precision tracking, a fast roll rate, wild tumbles, knife edge spins, and other maneuvers normally reserved for wood airplanes are all within the Veloxity's repertoire. With its consistent roll rate and arrow-straight tracking, the Veloxity may be the best rifle roll trainer out there! Of course, pull back on the throttle and the Veloxity will 3D with the best of them. A custom airfoil and carefully chosen moments means that smooth harriers upright, inverted, and rolling are stable and predictable, but not sloppy or imprecise...the Veloxity maintains precision through its whole flight envelope.
The Veloxity is happy flying on 3S batteries as small as 1300, or as large as 2200 for six solid minutes of high energy insanity.
Building the Veloxity is a snap. RCFactory's precision foam machining and laser cut wood, carbon, and fiberglass parts bond in quickly and easily into pre-cut slots and grooves. In many ways the Veloxity builds as easily as a 32" flat plane, and a couple of easy sessions is all you'll need to get it together and ready to rip. Controls are actuated with precision ball links that go together easily and pop off in a hard crash, saving servos.
Aspiring pilots need not fear the Veloxity! With reduced throws and the throttle pulled back a bit, it's an easy airplane to fly and is extremely predictable. It's a perfect step between 32" flat foamies and your first balsa bird. The super strong airframe means that less than perfect landings and the occasional dirt nap will not keep you grounded!

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 8x4.3 tum.
Passar perfekt på Tiger/SunnySky 2202/2204/2206.
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 9.5x3 tum.
Passar perfekt på Tiger AT2303/AT2206. Sunnysky 2206 1500kv.
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 9.5x2.5 tum.
Passar perfekt på Tiger AT2303/AT2206. Sunnysky 2206 1500kv.
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 9x4.3 tum.
Passar perfekt på Tiger AT2303/AT2206. Sunnysky 2206 1500kv
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

Smådelspacken till RCFactorys Click 21.

(Reservdelar).

This is a first model of a new line of 1m wingspan EPP models with increased stiffness and torsion rigidity.
We have beefed up everything, but especially the torsion rigidity of the fuselage - so that fuselage twist in fast rolling maneuvers is now totally a thing of the past.
The wing is thicker too, for better tolerance of the most insane, high-G stunts.

This model can also take a bigger motor up to the 2217 size, although it already flies nicely with 2212 motors. If you prefer insane power in your 3D models, this one is the ticket.

 Outdoor Series:

If you prefer bigger models with fully airfoiled wing, you can´t make a mistake with these. Developed by some of the best 3D pilots for a combination of 3D capability and easy, predictable handling.

Key Features
Wing span: 1000 mm
Length: 1020 mm
Weight: ca 500g depending on the equipment used
Motor: 2212 - 2217, 150 - 200W
Servos: 4x 9 - 12g
Receiver: micro, mini
ESC: 18A / 2A min.
Battery pack: 3s 1000 - 1500 mAh

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

 - Combo med vassare motor och värre servon! Rolig utomhuskärra!

Se hur den flyger under fliken "Videos" !

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 9x3.8 tum.
Passar perfekt på Tiger 2204/2206/AT2303. Sunnysky 2204/2206
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

COMBO Erbjuddande!

RC Factory Slick Superlite Golden.

Vektorstyrning ingår (valfritt att montera).

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory Slick Superlite Rainbow.

Vektorstyrning ingår (valfritt att montera).

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.


Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Nyhet från RC Factory! Slick Superlite Rainbow

Vektorstyrning ingår (valfritt att montera).


Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 830 mm
Längd: 888 mm
Flygvikt: ca 150 g inkl. batteri

OBS!

Tillägg till manualen: (Se bild 2)

1) The carbon stringers that you have to cut for the model are not the same length as the edge V3. The stringers going from the wing struts back are as follows:
#2 (cut 2) 150mm
#3 (cut 2) 139mm
#4 (cut 2) 137mm
#5 (cut 2) 127mm
#6 (cut 2) 160mm
#7 (cut 2) 123mm#1 (cut 2) go from the landing gear crossing area to the motor mount and need to be 110mm.

2) While bracing the ailerons, there are 2 flat 3mm x 150mm pieces that lay into the aileron tips that greatly help rigidity of the finished aileron. they are not mentioned in the manual so don't forget them. You want to put them in while the aileron is weighted down, ideally before the other bracing goes into the aileron.

Nyhet från RC Factory! Slick Superlite Golden

Vektorstyrning ingår (valfritt att montera).



Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 830 mm
Längd: 888 mm
Flygvikt: ca 150 g inkl. batteri

OBS!

Tillägg till manualen: (Se bild 2)

1) The carbon stringers that you have to cut for the model are not the same length as the edge V3. The stringers going from the wing struts back are as follows:
#2 (cut 2) 150mm
#3 (cut 2) 139mm
#4 (cut 2) 137mm
#5 (cut 2) 127mm
#6 (cut 2) 160mm
#7 (cut 2) 123mm

#1 (cut 2) go from the landing gear crossing area to the motor mount and need to be 110mm.

2) While bracing the ailerons, there are 2 flat 3mm x 150mm pieces that lay into the aileron tips that greatly help rigidity of the finished aileron. they are not mentioned in the manual so don't forget them. You want to put them in while the aileron is weighted down, ideally before the other bracing goes into the aileron.

Hardware for BACKYARD series models

Crack Yak, Edge, Extra Slick, Sbach

RC Factory Step One.

Enkelt nybörjar flygplan.

Specifikationer:

Material: EPP
Spännvidd: 850 mm
Längd: 720 mm
Flygvikt: ca 180 g inkl. batteri
Kanaler: 3
Servo: 2 st micro.
Ingår: Hjul, landställ och linkage.

Introducing the newest model from the production of RC Factory, a brand-new Step-One! The latest model of Backyard series has been designed by Jan Sedlacek, especially for beginner RC pilots, but also for fun of more experienced ones.
The construction is of standard EPP thickness, that is why is the Step One so resistant and almost unbreakable.
We have tried to make constructing the model as simple as possible, so that even an inexperienced modeler can built the model correctly and without complications. It is also subject to very detailed instructions.
Controlling the new Step One is nothing difficult, if observing the recommended settings. Controlled only by the engine power and rudder. The model is calm and stable in the air , yet for the first launches choose rather calm weather.
Easily removable wing makes transporting the plane no problem and so you can take it with you even on vacation. Model Step-One is supplied with the landing gear, so you can practice take-offs and landings on the ground. Due to the large wheels the Steop-One can handle even start from mown grass. When the landing gear is removed the flight performance gets even better. Always do take-offs and landings upwind, flight speed will get reduced and so you won't need that much of a space for your take-offs and landings. Avoid flying near high voltage wires and always remember, that even with so simple model, there can be done demage to property or to person's health.
Equipment for the model is chosen so that it could be used for our other products, such as models of "LITE series"
 
 
Backyard series:
This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

RC Factory Step One.

Enkelt nybörjar flygplan.

Specifikationer:

Material: EPP
Spännvidd: 850 mm
Längd: 720 mm
Flygvikt: ca 180 g inkl. batteri
Kanaler: 3
Servo: 2 st micro.
Ingår: Hjul, landställ och linkage.

Introducing the newest model from the production of RC Factory, a brand-new Step-One! The latest model of Backyard series has been designed by Jan Sedlacek, especially for beginner RC pilots, but also for fun of more experienced ones.
The construction is of standard EPP thickness, that is why is the Step One so resistant and almost unbreakable.
We have tried to make constructing the model as simple as possible, so that even an inexperienced modeler can built the model correctly and without complications. It is also subject to very detailed instructions.
Controlling the new Step One is nothing difficult, if observing the recommended settings. Controlled only by the engine power and rudder. The model is calm and stable in the air , yet for the first launches choose rather calm weather.
Easily removable wing makes transporting the plane no problem and so you can take it with you even on vacation. Model Step-One is supplied with the landing gear, so you can practice take-offs and landings on the ground. Due to the large wheels the Steop-One can handle even start from mown grass. When the landing gear is removed the flight performance gets even better. Always do take-offs and landings upwind, flight speed will get reduced and so you won't need that much of a space for your take-offs and landings. Avoid flying near high voltage wires and always remember, that even with so simple model, there can be done demage to property or to person's health.
Equipment for the model is chosen so that it could be used for our other products, such as models of "LITE series"
 
 
Backyard series:
This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

COMBO Erbjudande!

RC Factory MXS-C Mini Röd.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory Lil Fokker Gul/Grön!

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory Lil Fokker Röd!

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory SU29 Russian SuperLite!

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory Crack Laser Lite!

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri. (300-2S, 450-2S)

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjuddande!

RC Factory Crack Laser Lite!

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri. (300-2S, 450-2S)

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

Komplettera med batteri. (GensAce 450-3)

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

The Flash is an improvement of the original 3D trainer that used to be produced under the same name. Although the main parameters remained the same, the model was totally re-engineered for easier and straightforward build.

The model, which was originally designed as all-around 3D trainer capable of anything you might ask from it, was re-introduced after concentrated demand from our customers.

You will appreciate the forgiving characteristics and smooth, linear response of this model - it will make your learning new 3D maneuvers a breeze.

Key Features
Wing span: 1000 mm
Length: 1020 mm
AUW: 350 - 420 g
Motor: 100 - 200 W
ESC: 15 - 20 A
Servo: 4 x 9 - 12 g
Battery: 650 - 1200 3S
Prop: 9/ 4 - 5

The Flash is an improvement of the original 3D trainer that used to be produced under the same name. Although the main parameters remained the same, the model was totally re-engineered for easier and straightforward build.

The model, which was originally designed as all-around 3D trainer capable of anything you might ask from it, was re-introduced after concentrated demand from our customers.

You will appreciate the forgiving characteristics and smooth, linear response of this model - it will make your learning new 3D maneuvers a breeze.

Key Features
Wing span: 1000 mm
Length: 1020 mm
AUW: 350 - 420 g
Motor: 100 - 200 W
ESC: 15 - 20 A
Servo: 4 x 9 - 12 g
Battery: 650 - 1200 3S
Prop: 9/ 4 - 5

Litet kastflygplan från RCFactory.

Kul för små barn! Hållbart.

Inställbar tyngdpunkt.
Osorterade färger.

Lil Fokker!

Specifikation:
Vingspann: 680 mm.
Kroppslängd: 650 mm
Flygvikt: från 130 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Lil Fokker!

Specifikation:
Vingspann: 680 mm.
Kroppslängd: 650 mm
Flygvikt: från 130 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Kolfiberpropeller Indoor.

Antal: 1 st
Märke: PT
Storlek: 7x3.5 tum.
Passar perfekt på Tiger/SunnySky 2202/2204/2206.
(Sitter perfekt utan adapter)

Ultralätt och superkvalité.

För den som vill ha det värsta!

Crack LaserPro Techno
Presenting the Crack Laser Pro! Built with thin but rigid and durable EPP foam, extensive carbon fiber bracing and reinforcement, and world-class design, the Crack Laser Pro aims to be the most precise, stable, and sharp small freestyle airplane the world has ever seen.
The original Crack Laser was a precision freestyle monster, designed to take advantage of everything the "Lite" construction had to offer.  Not just a re-casting of the Crack Laser with Super Lite construction, every line, moment, and area of the Crack Laser Pro has been breathed upon to take full advantage of the lighter weight, better aerodynamic properties, and increased rigidity of this build style.
Equipped with a proven and bulletproof power combo (including metal geared servos!), the Crack Laser Pro is simply breathtaking in the air. It combines a huge speed range with lightning quick aileron response, zero-rock harriers, and of course, dead true knife edge. Despite its low wing loading, it never feels sluggish. The Crack Laser Pro is gentle and forgiving for newer pilots while remaining extremely satisfying to freestyle hot shots.

Wing span 805 mm
Length 845 mm
AUW up 160 g
Motor 60 - 80W
ESC 10 - 12A
Servo 2x 6g, 1x 9g
Battery 2s lipo pack 300 mAh
Propeller 8/4

RC Factory Edge XL

Se film under fliken "Videos"!!


Vingspann: 1060 mm.
Kroppslängd: 1120 mm
Flygvikt: 680 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Edge XL
Go insane! From the realm of "flies like balsa, costs and repairs like foam" arrived a new plane, the Edge XL.
 
Loosely based on the full size Edge, the unmatched Red Bull Air Race (TM) competitor, the designer's goal was to make something that flies at least as good as the legendary Cody Wojcik's Veloxity while having somewhat different looks. You be the judge how well RC Factory managed to achieve this goal.
 
The early testers' response is extremely encouraging: Jan Votava, junior European F3A champion and World vice-champion, who was originally quite skeptical about this size of models, admitted that he never expected anything like that - yet now he is jumping up and down with excitement. "Everybody is going to love this" was his verdict, just as he never bothered with 3s and loaded the plane with his 1500 mAh, 4s copter battery pack rated at 95C. "The plane goes ballistic and there is nothing it can't do", says Votava.
 
Insane roll rate, great linear response to all controls, whip-like snap rolls, very steady hover, smooth performance on low rates but total madness on high ones. If you are looking for an insane piece of equipment to wow your friends, look no further.

Crack Camel

Specifikation:
Vingspann: 875 mm.
Kroppslängd: 720 mm
Flygvikt: från 250 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Crack Camel Silver:
We're breaking all the rules yet again with our new Crack Camel! Twisted Hobbys has taken the feel and concept of WWI flying machines and daredevil pilots to fantastic new places. Our customers have asked for us to create a worthy adversary to the well known Crack Fokker so they can duel it out in 3D flying and WWI dog-fighting. With a wide speed range, and silly aerobatics for more fun than you can imagine our Crack Camel with not disappoint!
Paint and art work was inspired by one of the classic schemes, keeping true to the Sopwith Camel's roots. Like all Twisted Hobbys models quality is superior and building is a pleasure with the latest 3d printed hardware that eliminates excess weight, increased durability while removing any unwanted play from all the control surface connections.
Twisted Hobbys as always has spent time selecting the correctly matched electronics for the Crack Camel, available as a convenient power combo. Recommended stock setup is 2s 600 mah w/ 9x4.7 or 3s 450 mah w/ 8x4, 9x5 for advanced pilots. Enjoy the look of a classic Sopwith Camel with flight characteristics you have only dreamed of now its time to take on the Fokker Dr.1!

Crack Camel

Specifikation:
Vingspann: 875 mm.
Kroppslängd: 720 mm
Flygvikt: från 250 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Crack Camel Silver:
We're breaking all the rules yet again with our new Crack Camel! Twisted Hobbys has taken the feel and concept of WWI flying machines and daredevil pilots to fantastic new places. Our customers have asked for us to create a worthy adversary to the well known Crack Fokker so they can duel it out in 3D flying and WWI dog-fighting. With a wide speed range, and silly aerobatics for more fun than you can imagine our Crack Camel with not disappoint!
Paint and art work was inspired by one of the classic schemes, keeping true to the Sopwith Camel's roots. Like all Twisted Hobbys models quality is superior and building is a pleasure with the latest 3d printed hardware that eliminates excess weight, increased durability while removing any unwanted play from all the control surface connections.
Twisted Hobbys as always has spent time selecting the correctly matched electronics for the Crack Camel, available as a convenient power combo. Recommended stock setup is 2s 600 mah w/ 9x4.7 or 3s 450 mah w/ 8x4, 9x5 for advanced pilots. Enjoy the look of a classic Sopwith Camel with flight characteristics you have only dreamed of now its time to take on the Fokker Dr.1!

COMBO Erbjudande!

RC Factory Extra 330 SuperLITE Röd.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Extra 330 SuperLITE Grön.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Edge 540 Mini Röd.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Edge 540 Mini Gul.

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO Erbjudande!

RC Factory Edge 540 V3 SuperLite FreakShow.

(2 st ES08D, Vektorstyrning!)

OBS! Setupen är avsedd endast för 2S Lipo (7.4V) batteri.

Komplettera med batteri ex. Tattu 300 mAh 2S 75C. och kabel/kontakter.

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

RC Factory Crack Fokker.

Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 890 mm
Längd: 860 mm
Flygvikt: ca 250 g inkl. batteri


35" EPP Crack Fokker Dr.1 Triplane
 
We're breaking the rules again with the Crack Fokker Dr.1 by creating yet another chapter in our Crack Series in-line up. Inspired by the original Fokker Dr.1 with design and sculpting from our top team pilot and designer Cody Wojcik... this Fokker is ready to blow you away!
 
With a whole new set of flight characteristics the Crack Fokker is like no other model we have. Loops are beyond tight and roll rate is extremely axial and quick for the amount of wing area. The Fokker can be flown so slow it can fool someone into thinking it’s in slow motion! The fun doesn’t stop there, with dual aileron servos you can even add mixing for multiple flap settings to create different post stalls and even tighter loops then we have ever experience before. The Crack Fokker has impressed all our team members and also anyone that has flown it. The Crack Fokker has become our new favorite drug of choice and we are proud to share with all of you.
 
Paint and art work was inspired by one of the classic schemes keeping true to its roots with some major hidden performance just waiting to be unleashed. Like all RC Factory & Twisted Hobbys models quality is beyond questioning and building is a breeze with latest construction hardware that eliminating excess weight as well as removing any unwanted play from all the control surface connections.
 
RC Factory & Twisted Hobbys has focused on selecting the correct matched electronics for the Crack Fokker which can be purchased separately on our web site. Recommended stock setup is 2s 600mah GWS 9x5 setup  or extreme setup is 3s 450mah GWS 8x4. Enjoy the look of a classic Fokker Dr.1 with flight characteristics you have only dreamed of!

RC Factory Crack Fokker.

Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 890 mm
Längd: 860 mm
Flygvikt: ca 250 g inkl. batteri


35" EPP Crack Fokker Dr.1 Triplane
 
We're breaking the rules again with the Crack Fokker Dr.1 by creating yet another chapter in our Crack Series in-line up. Inspired by the original Fokker Dr.1 with design and sculpting from our top team pilot and designer Cody Wojcik... this Fokker is ready to blow you away!
 
With a whole new set of flight characteristics the Crack Fokker is like no other model we have. Loops are beyond tight and roll rate is extremely axial and quick for the amount of wing area. The Fokker can be flown so slow it can fool someone into thinking it’s in slow motion! The fun doesn’t stop there, with dual aileron servos you can even add mixing for multiple flap settings to create different post stalls and even tighter loops then we have ever experience before. The Crack Fokker has impressed all our team members and also anyone that has flown it. The Crack Fokker has become our new favorite drug of choice and we are proud to share with all of you.
 
Paint and art work was inspired by one of the classic schemes keeping true to its roots with some major hidden performance just waiting to be unleashed. Like all RC Factory & Twisted Hobbys models quality is beyond questioning and building is a breeze with latest construction hardware that eliminating excess weight as well as removing any unwanted play from all the control surface connections.
 
RC Factory & Twisted Hobbys has focused on selecting the correct matched electronics for the Crack Fokker which can be purchased separately on our web site. Recommended stock setup is 2s 600mah GWS 9x5 setup  or extreme setup is 3s 450mah GWS 8x4. Enjoy the look of a classic Fokker Dr.1 with flight characteristics you have only dreamed of!

RC Factory Crack Fokker.

Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 890 mm
Längd: 860 mm
Flygvikt: ca 250 g inkl. batteri


35" EPP Crack Fokker Dr.1 Triplane
 
We're breaking the rules again with the Crack Fokker Dr.1 by creating yet another chapter in our Crack Series in-line up. Inspired by the original Fokker Dr.1 with design and sculpting from our top team pilot and designer Cody Wojcik... this Fokker is ready to blow you away!
 
With a whole new set of flight characteristics the Crack Fokker is like no other model we have. Loops are beyond tight and roll rate is extremely axial and quick for the amount of wing area. The Fokker can be flown so slow it can fool someone into thinking it’s in slow motion! The fun doesn’t stop there, with dual aileron servos you can even add mixing for multiple flap settings to create different post stalls and even tighter loops then we have ever experience before. The Crack Fokker has impressed all our team members and also anyone that has flown it. The Crack Fokker has become our new favorite drug of choice and we are proud to share with all of you.
 
Paint and art work was inspired by one of the classic schemes keeping true to its roots with some major hidden performance just waiting to be unleashed. Like all RC Factory & Twisted Hobbys models quality is beyond questioning and building is a breeze with latest construction hardware that eliminating excess weight as well as removing any unwanted play from all the control surface connections.
 
RC Factory & Twisted Hobbys has focused on selecting the correct matched electronics for the Crack Fokker which can be purchased separately on our web site. Recommended stock setup is 2s 600mah GWS 9x5 setup  or extreme setup is 3s 450mah GWS 8x4. Enjoy the look of a classic Fokker Dr.1 with flight characteristics you have only dreamed of!

Dubbeldäckare från RC Factory!

Idealisk 3D trainer, helt i EPP.
Byggs ihop på 1-2 kvällar
Levereras med landningsställ av kolfiber
Lagas enkelt med vanligt CA lim om olyckan skulle vara framme

Specifikation:
Vingspann: 940 mm.
Kroppslängd: 1000 mm
Flygvikt: från 475 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Revo P3 is a super-acrobatic biplane inspired by an actual aircraft.
With its size it expands the range of our "one meter" models.
Not just the new wing profile, that we developed specifically for this model, contributes to its excellent flight characteristics, but also the overall layout and model geometry,which allows precise flying from basic acrobatics to aggressive 3D maneuvers.
What type of flying you choose depends entirely on you.
Low weight and a new model concept increases its durability.
Revo P3 model is manufactured by modern CNC technology with the most prepared parts,
so that the assembly is easy as possible for you.

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

COMBO  - erbjudande!

OBS! Paketet går ej att ändra på! Tillfälligt erbjudande!

Komplettera med LiPo-acc (1800-3S) och radioutrustning.

Specifikation:
Serie: "Racer series"
Vingspann: 780 mm.
Kroppslängd: 720 mm
Flygvikt: 230 g.
Funktioner: Skev, höjd, sida och gas. (4 kanaler/3 servon).
Ingår: Linkage/kolfiber.

Liten kundrecension:
Har nu provflugit RC Factory P51 Röd och är supernöjd! Vad fint den går i luften med mina 2S och snabbare vore jobbigt.
Provflög min RC Factory P51 RED och tyckte det var kyttigt och turbulent När jag sedan ökade expo till 35% så insåg att det var jag själv som var orsaken Modellen reagerar perfekt på styrning. Den är ganska snabb på 2S 650mAh ack med RS2205 motor. (Underbar motor för 2-4 celler). Måste vara skrämmande snabb på 4S. Inget för en 69 åring.
Kompakt modell som klarar vind och flyger superfint. Finns i blå och röd dekor men kroppen skiljer sig lite. Röd passar mig bäst.


"
From the team that dominates the backyard and park 3D foamy scene comes something new, fast, and fun! The Twisted Racers are the coolest thing around for (in)formal club pylon racing, aerobatics, or just plain fun sport flying. Nearly indestructible, these models are ideal for bashing around or flying with friends who don't always yield the right of way. Two aircraft, the Nemesis and Mustang, based on full-scale Reno racing classics, available in two schemes each mean that everybody gets to fly something unique and stay competitive!
RC Factoy & Twisted Hobbys again brings you the killer combination of Cody Wojcik's design approach and RCFactory's world class construction methods and stunning artwork. The result is an aircraft that builds with extreme ease...just a few hours is all you need. Once airborne, the Racers track along with perfect, stable manners, effortlessly carving through high-speed aerobatics or pulling high-G turns on an improvised pylon course.
Flying on the proven and affordable power combo also used in the standard 32" 3D aircraft such as the Crack Yak and Edge, the Racers easily achieve 6 minute flights with a 3S 600 mah battery."

Specifikation:
Serie: "Racer series"
Vingspann: 780 mm.
Kroppslängd: 720 mm
Flygvikt: 230 g.
Funktioner: Skev, höjd, sida och gas. (4 kanaler/3 servon).
Ingår: Linkage/kolfiber.

Liten kundrecension:
Har nu provflugit RC Factory P51 Röd och är supernöjd! Vad fint den går i luften med mina 2S och snabbare vore jobbigt.
Provflög min RC Factory P51 RED och tyckte det var kyttigt och turbulent När jag sedan ökade expo till 35% så insåg att det var jag själv som var orsaken Modellen reagerar perfekt på styrning. Den är ganska snabb på 2S 650mAh ack med RS2205 motor. (Underbar motor för 2-4 celler). Måste vara skrämmande snabb på 4S. Inget för en 69 åring.
Kompakt modell som klarar vind och flyger superfint. Finns i blå och röd dekor men kroppen skiljer sig lite. Röd passar mig bäst.

"
From the team that dominates the backyard and park 3D foamy scene comes something new, fast, and fun! The Twisted Racers are the coolest thing around for (in)formal club pylon racing, aerobatics, or just plain fun sport flying. Nearly indestructible, these models are ideal for bashing around or flying with friends who don't always yield the right of way. Two aircraft, the Nemesis and Mustang, based on full-scale Reno racing classics, available in two schemes each mean that everybody gets to fly something unique and stay competitive!
RC Factoy & Twisted Hobbys again brings you the killer combination of Cody Wojcik's design approach and RCFactory's world class construction methods and stunning artwork. The result is an aircraft that builds with extreme ease...just a few hours is all you need. Once airborne, the Racers track along with perfect, stable manners, effortlessly carving through high-speed aerobatics or pulling high-G turns on an improvised pylon course.
Flying on the proven and affordable power combo also used in the standard 32" 3D aircraft such as the Crack Yak and Edge, the Racers easily achieve 6 minute flights with a 3S 600 mah battery."

Specifikation:
Vingspann: 1070 mm.
Kroppslängd: 1120 mm
Flygvikt: ca 550 g.
Funktioner: Skev, höjd, sida och gas. (5 kanaler).
Ingår: Hjul, landställ och linkage/kolfiber.

Veloxity
 
From the Twisted mind of Cody Wojcik comes the Veloxity! Loosely based on the full-scale Velox Revolution 1, the Veloxity delivers an experience never before available in a foam plane. As one of the stiffest foam airframes around, precision tracking, a fast roll rate, wild tumbles, knife edge spins, and other maneuvers normally reserved for wood airplanes are all within the Veloxity's repertoire. With its consistent roll rate and arrow-straight tracking, the Veloxity may be the best rifle roll trainer out there! Of course, pull back on the throttle and the Veloxity will 3D with the best of them. A custom airfoil and carefully chosen moments means that smooth harriers upright, inverted, and rolling are stable and predictable, but not sloppy or imprecise...the Veloxity maintains precision through its whole flight envelope.
The Veloxity is happy flying on 3S batteries as small as 1300, or as large as 2200 for six solid minutes of high energy insanity.
Building the Veloxity is a snap. RCFactory's precision foam machining and laser cut wood, carbon, and fiberglass parts bond in quickly and easily into pre-cut slots and grooves. In many ways the Veloxity builds as easily as a 32" flat plane, and a couple of easy sessions is all you'll need to get it together and ready to rip. Controls are actuated with precision ball links that go together easily and pop off in a hard crash, saving servos.
Aspiring pilots need not fear the Veloxity! With reduced throws and the throttle pulled back a bit, it's an easy airplane to fly and is extremely predictable. It's a perfect step between 32" flat foamies and your first balsa bird. The super strong airframe means that less than perfect landings and the occasional dirt nap will not keep you grounded!

RC Factory Step One.

Enkelt nybörjar flygplan.

Specifikationer:

Material: EPP
Spännvidd: 850 mm
Längd: 720 mm
Flygvikt: ca 180 g inkl. batteri
Kanaler: 3
Servo: 2 st micro.
Ingår: Hjul, landställ och linkage.

Introducing the newest model from the production of RC Factory, a brand-new Step-One! The latest model of Backyard series has been designed by Jan Sedlacek, especially for beginner RC pilots, but also for fun of more experienced ones.
The construction is of standard EPP thickness, that is why is the Step One so resistant and almost unbreakable.
We have tried to make constructing the model as simple as possible, so that even an inexperienced modeler can built the model correctly and without complications. It is also subject to very detailed instructions.
Controlling the new Step One is nothing difficult, if observing the recommended settings. Controlled only by the engine power and rudder. The model is calm and stable in the air , yet for the first launches choose rather calm weather.
Easily removable wing makes transporting the plane no problem and so you can take it with you even on vacation. Model Step-One is supplied with the landing gear, so you can practice take-offs and landings on the ground. Due to the large wheels the Steop-One can handle even start from mown grass. When the landing gear is removed the flight performance gets even better. Always do take-offs and landings upwind, flight speed will get reduced and so you won't need that much of a space for your take-offs and landings. Avoid flying near high voltage wires and always remember, that even with so simple model, there can be done demage to property or to person's health.
Equipment for the model is chosen so that it could be used for our other products, such as models of "LITE series"
 
 
Backyard series:
This is the classic, very popular 3D EPP line. The rugged construction allows you to learn all kinds of new maneuvers without fear of destroying your model.

Edge 540 V3 SuperLITE

Vektorstyrning ingår, valbart att bygga med eller utan.


Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 840 mm
Längd: 900 mm
Flygvikt: ca 150 g inkl. batteri


This amazing model is the result of more than 3 years of refining and development by the indoor aerobatic pioneer and World Air Games competitor Jan Spatny. Oversize controls, the right distribution of fuselage side area and side-to-side thrust vectoring give this model some truly unique abilities. Whip-like snap rolls, tight knife edge loops or any other maneuver you can think of, there is nothing this plane couldn't do. Light 4mm EPP construction gives the model flying qualities on par with the best milled-out Depron planes, with the added advantage of much better durability.

Edge 540 V3 SuperLITE

Vektorstyrning ingår, valbart att bygga med eller utan.


Specifikationer:
Serie: Indoor EPP
Material: EPP
Spännvidd: 840 mm
Längd: 900 mm
Flygvikt: ca 150 g inkl. batteri


This amazing model is the result of more than 3 years of refining and development by the indoor aerobatic pioneer and World Air Games competitor Jan Spatny. Oversize controls, the right distribution of fuselage side area and side-to-side thrust vectoring give this model some truly unique abilities. Whip-like snap rolls, tight knife edge loops or any other maneuver you can think of, there is nothing this plane couldn't do. Light 4mm EPP construction gives the model flying qualities on par with the best milled-out Depron planes, with the added advantage of much better durability.